REICHELT IE: Microphones
The Best
DELOCK 66499 - Microphone, USB, with Gooseneck
33.67 EUR
This USB microphone by Delock can be used for voice and vocal transmissions.Optimal recordings
The microphone has a cardioid polar pattern (unidirectional) and captures the sound ideally. Due to a high power, low self-noise and precise performance, even the finest sounds are optimally recorded.
Mute button & LED ring
With the mute button in the middle of the microphone, the microphone can be quickly muted. The LED ring signals operational status with a blue or red light.
Flexible gooseneck
With the gooseneck, the microphone can be bent in the preferred direction.
Plug & Play
Due to USB Plug & Play the microphone is ready to use immediately, no driver installation is needed. The microphone works with all common operating systems such as Windows, Mac OS, Chrome OS and Linux.
Specification
- Connector: 1 x USB 2.0 Type-A male
- Directivity: unidirectional
- Sensitivity: -35 dB +/- 3 dB
- Frequency range: 70 Hz - 15 kHz
- Sample rate: 16 Bit / 48 kHz
- Mute-Button
- Gooseneck, length ca. 7 cm
- Status LED
- Dimensions (LxWxH): ca. 196 x 23 x 23 mm
- USB bus powered
- Plug & Play
System requirements
- Chrome OS
- Linux Kernel 3.3 or above
- Mac OS 10.9 or above
- Windows 8.1/8.1-64/10/10-64
- PC or laptop with a free USB Type-A port
Top Pick
DELOCK 66640 - Microphone, XLR connector / 3 pin stereo jack male, adapter cabl
46.08 EUR
Professional Computer Podcasting Microphone with XLR connector and 3 pin stereo jack male + adapter cable for Smartphone and TabletThis professional condenser microphone by Delock can be used for high-quality voice and vocal recordings.
Optimal recordings
The microphone has a high-quality 16 mm condenser chip and a cardioid polar pattern (unidirectional) and therefore ideally captures the sound. Due to high power, low self-noise and precise performance, even the finest sounds are recorded crystal clear.
Good windscreen
Due to the included windscreen, the recording quality is further optimized. Disturbing wind noises are optimally filtered.
Multifunctional application
It can be connected to any PC or laptop via the detachable XLR to 3 pin stero jack cable. With the included 4 pin Y-adapter cable, it can also be connected to a tablet or smartphone.
Stable & non-slip stand
The metal stand with rubber feet ensures that the microphone stands stable on the table. The microphone holder can be adjusted in a 180° angle as required. The table stand can be easily folded and transported when needed.
Specification
- Connector: 1 x XLR plug
- Cable:
1 x XLR jack >
1 x 3.5 mm 3 pin stereo jack male - Y-Adapter:
1 x 3.5 mm 4 pin stereo jack male (CTIA standard) >
1 x 3.5 mm 3 pin stereo jack female microphone
1 x 3.5 mm 3 pin stereo jack female headset - Directivity: unidirectional
- Sensitivity: -38 dB +/- 3 dB
- Frequency range: 30 Hz - 16 kHz
- Signal-to-noise ratio (SNR): ca. 70 dB
- Self-Noise: max. 16 dBA
- Sound pressure level (SPL): max. 120 dB
- Cable length: ca. 2.5 m
- Colour: black
- Voltage: 1.5 V
System requirements
- a free stereo port 3.5 mm
Package content
- XLR microphone
- XLR to stereo jack cable
- Y-adapter cable
- Windscreen
- Microphone holder
- Table stand
Package
- Retail Box
Excellent
DELOCK 66582 - condenser directional microphone, Smartphones and DSLR Cameras
51.24 EUR
This professional condenser directional microphone by Delock can be used for high-quality voice and vocal recordings.Optimal recordings
The microphone has a supercardioid polar pattern and therefore captures the sound ideally. Due to its high power, low self-noise and precise performance, even the finest sounds are recorded crystal clear. Annoying background noises are minimized.
Good windscreen
Due to the included windscreen, the recording quality is further optimized. Disturbing wind noises are optimally filtered.
High compatibility
With its 3.5 mm 4 pin stereo jack male, the microphone is compatible with various smartphones. Due to the included 3.5 mm TRS female adapter, the microphone can also be connected to various DSLR cameras and computers. With the hot shoe adapter, the microphone can be mounted on an accessory shoe of cameras.
No batteries required
The microphone is passive and therefore does not need batteries. This eliminates the need to change batteries.
Stable & non-slip stand
The metal stand with rubber feet ensures that the microphone stands firmly on the table. The adjustable smartphone clamp ensures a smooth recording. The rubberized clamps prevent smartphones from being scratched. The flexible smartphone clamp holds devices with a width of up to 8.5 cm. The ball joint can be rotated by 360° and locked in place. The table stand can be easily unscrewed and folded up when needed.
Specification
- Connector: 1 x 3.5 mm 4 pin stereo jack female
- Coiled Cable: 1 x 3.5 mm 4 pin audio stereo jack male > 1 x 3.5 mm 4 pin audio stereo jack male
- Adapter: 1 x 3.5 mm 4 pin stereo jack female > 1 x 3.5 mm 3 pin stereo jack male (TRRS to TRS)
- Directivity: supercardioid
- Sensitivity: -23 dB +/- 3 dB
- Frequency range: 20 Hz - 12 kHz
- Signal-to-noise ratio (SNR): ca. 70 dB
- Sound pressure level (SPL): max. 110 dB
- Metal stand: Ø ca. 180 mm
- Microphone length: ca. 150 mm
- Smartphone clamp: width up to 8.5 cm
- Hot shoe adapter for mounting on cameras with accessory shoe
System requirements
- A free stereo port 3.5 mm
Package content
- Microphone
- Stereo jack adapter
- Coiled cable, length ca. 10 cm - 60 cm
- Table stand
- Flexible smartphone clamp
- Windscreen
- User manual
Recommended
DELOCK 66279 - Tie Lavalier Microphone Omnidirectional with Clip 3.5 mm
33.67 EUR
This tie lavalier microphone by Delock is designed for mobile use and hands-free recording.With clip to attach
It can easily be clipped to a tie or collar.
Optimal recordings
The omnidirectional polar pattern captures the sound optimally and achieves a high recording quality. This makes it ideal for skyping, interviews, voice recordings, etc.
Multifunctional application
It can be connected to any PC or laptop via the 3 pin stereo jack connector. The 4 pin Y-adapter included in the delivery also allows connection to a tablet or smartphone.
Specification
• Connector:
1 x 3.5 mm 3 pin stereo jack male
• Y-Adapter:
1 x 3.5 mm 4 pin stereo jack male (CTIA standard) >
1 x 3.5 mm 3 pin stereo jack female microphone
1 x 3.5 mm 3 pin stereo jack female headset
• Directivity: omnidirectional
• Impedance: 2.2 kOhm
• Sensitivity: -30 dB +/- 3 dB
• Frequency range: 50 Hz - 16 kHz
• Housing material: metal
• Weight: ca. 15.5 g
• Cable length: ca. 1.8 m
System requirements
• A free stereo port 3.5 mm
Package content
• Microphone
• Clip
• Y-Adapter
• Windscreen
• Storage bag
Package
• Retail Box
Featured
DELOCK 65872 - Microphone for smartphone/tablet, 3.5-mm jack, white
26.44 EUR
This microphone by Delock is suitable for mobile use with a smartphone or tablet and can be used for voice and vocal transmissions. The rubberised base provides a non-slip stand and the microphone can be turned in any direction by using the gooseneck. The microphone also has a 3.5-mm stereo jack female port, meaning that headphones can be used at the same time.Specifications
- Connections:
1x 3.5-mm 4-pin jack (male)
1 x 3.5-mm 3-pin jack socket - Directional pattern: omnidirectional
- Impedance: 2.2 kOhm
- Sensitivity: -32 dB +/- 3 dB
- Frequency range: 100 Hz - 13 kHz
- Dimensions: (L x W x H): approx. 55 x 64 x 143 mm
- Weight: approx. 88 g
- Cable length: approx. 1.7 m
Alternative
DELOCK 65868 - USB Microphone, base, Touch-Mute Button
38.84 EUR
This USB microphone by Delock can be used for voice and vocal transmissions. The rubberized base provides a non-slip stand and the gooseneck allows the microphone to bend in the ideal direction. The LED ring indicates that the microphone is ready for operation by means of a blue or red light and the touch mute button can be used to mute the microphone.Specification
- Connector: 1 x USB 2.0 Type-A reversible male
- Sensitivity: -37 dB +/- 3 dB
- Frequency range: 70 Hz - 15 kHz
- Impedance: 2.2 kOhm +/- 30% at 1 kHz
- Sample rate: 16 Bit / 48 kHz
- Touch Mute-Button
- Gooseneck
- Status LED
- Rubber Base
- Colour: black
- Cable length: ca. 1.7 m
- Dimensions (LxWxH): ca. 140 x 60 x 60 mm
- USB bus powered
- Plug & Play
System requirements
- Windows 7/7-64/8.1/8.1-64/10/10-64, Linux ex Kernel 3.3 / Kernel 4.9.x, Mac ex OS 10.9
- PC or laptop with a free USB Type-A port
Package content
- USB-microphone
- User manual
DELOCK 65871 - USB Microphone, base, Mute Button
46.08 EUR
This USB microphone by Delock can be used for voice and vocal transmissions. The rubberized base provides a non-slip stand and the gooseneck allows the microphone to bend in the ideal direction. The LED ring and the green LED indicate operability and mute activation or deactivation by means of blue or red light. The Mute button mutes the microphone and the ON button switches it on and off.Specification
- Connector: 1 x USB 2.0 Type-A reversible male
- Directivity: uni-directional
- Sensitivity: -44 dB +/- 3 dB
- Frequency range: 70 Hz - 9 kHz
- Sample rate: 16 Bit / 48 kHz
- Function key: 1 x On / Off switch, 1 x mute switch
- Gooseneck, length ca. 25 cm
- Status LED
- Rubber Base
- Colour: black
- Cable length: ca. 1.7 m
- Dimensions (LxWxH): ca. 120 x 85 x 320 mm
- USB bus powered
- Plug & Play
System requirements
- Windows 7/7-64/8.1/8.1-64/10/10-64, ex Linux Kernel 3.3, ex Mac OS 10.9
- PC or laptop with a free USB Type-A port
Package content
- USB microphone
- User manual
Package
- Retail Box
DELOCK 66331 - USB Condenser Microphone Set - for Podcasting, Gaming and Vocals
53.31 EUR
This USB condenser microphone by Delock can be used for high-quality voice and vocal recordings.Optimal recordings
The microphone has a cardioid polar pattern (unidirectional) and captures the sound ideally. Due to a high power, low self-noise and precise performance, even the finest sounds are optimally recorded.
Dual Layer Pop Filter & Windscreen
Due to the included dual layer pop filter and the windscreen, the recording quality is further optimized. Annoying wind noises are optimally filtered.
Plug & Play
Due to USB Plug & Play the microphone is ready to use immediately, no driver installation is needed. The microphone works with all common operating systems such as Windows, Mac OS, Chrome OS and Linux.
Stable & non-slip stand
The metal base with rubber feet ensures that the microphone stands stable on the table. The shock mount (spider) ensures vibration-free recording. The table stand can be folded and transported easily if required.
Specification
- Connector: 1 x USB 2.0 Type-A male
- Directivity: unidirectional
- Sensitivity: -47 dB +/- 3 dB
- Frequency range: 20 Hz - 20 kHz
- Sample rate: 16 Bit / 44.1 kHz
- Signal-to-noise ratio (SNR): ca. 60 dB
- Impedance: 2.2 kOhm
- Cable length: ca. 1.5 m
- Colour: black
- Dimensions (LxWxH): ca. 150 x 45 x 35 mm
- USB bus powered
- Plug & Play
System requirements
- Chrome OS
- Linux Kernel 4.4 or above
- Mac OS 10.9 or above
- Windows 7/7-64/8.1/8.1-64/10/10-64
- PC or laptop with a free USB Type-A port
Package content
- USB microphone
- Table stand
- Shock mount (spider)
- Pop filter
- Windscreen
- User manual
CHERRY JA-0720 - Microphone, USB-C, with RGB illumination
124.68 EUR
USB microphone for streaming and gaming with impressive RGB illumination- Elegant matt copper design
- Stylish three-legged stand made of solid metal with integrated vibration damper
- Versatile thanks to four different directional characteristics: Cardioid, omnidirectional, bidirectional and stereo
- Impressive RGB illumination for an intense gaming or streaming setup
- Gain controller for adjusting the microphone sensitivity
- Compatible with PC, Mac, PS4 and PS5 (plug & play via USB cable)
- Convenient touch-to-mute function
- Headphone jack with integrated volume control in CHERRY design
- Shock mount for superior sound quality without unwanted noise or vibration
The CHERRY UM 9.0 PRO RGB not only impresses with its three-legged stand made of solid metal, which ensures stability, but is also visually striking. Matt black meets stylish copper, which makes this professional USB microphone stand out.
Included in delivery
- Microphone
- USB cable
- User manual
RØDE RODE NTUSB MINI - USB condenser microphone
113.26 EUR
STUDIO-QUALITY USB MICROPHONE- High-quality condenser capsule that delivers warmth and presence for a clear, professional sound.
- Directional cardioid pickup pattern optimised to reduce room sound and other extraneous noise.
- Smooth frequency response that sounds incredible in a wide variety of applications.
- In-built pop filter for reducing plosives.
- Unique detachable magnetic desk stand to mitigate knocks and bumps and is easy to remove.
- Integrated 360-degree swing mount for quick and easy positioning on a desktop, mic stand, or studio arm.
- Studio-grade headphone amplifier with precision level control and switchable zero-latency monitoring for eliminating distracting echo.
- Class-compliant USB output that works seamlessly with computers and tablets, simple to use – just plug in and hit record.
The NT-USB Mini brings the pristine sound quality of RØDE’s world-class studio mics to a compact, easy-to-use desktop USB microphone. Designed to deliver crystal-clear, professional-sounding audio direct to a computer or tablet, it’s the perfect microphone for gamers, podcasters, musicians, streamers, business professionals and content creators who want to be heard in full definition.
The NT-USB Mini features a studio-grade headphone amplifier and a high-quality 3.5mm headphone output, complete with precision volume control, allowing you to easily monitor your audio. There is also a switchable zero-latency monitoring mode for eliminating distracting echo when tracking vocals or recording instruments. It is incredibly easy to set up and use, with simple controls, an in-built pop filter and a class-compliant USB output that works seamlessly with computers or tablets, no drivers or software needed. Just plug into your Mac, PC or tablet with the included USB cable and hit record.
The NT-USB Mini features a unique detachable magnetic desk stand – not only does this provide a sturdy base on any desktop, it also makes it easy to remove and attach to a mic stand or studio arm. This and the unique 360-degree swing mount means you can position the mic wherever it needs to be to get the best recording possible.
The NT-USB Mini is the perfect addition to any desktop or home studio setup. At just 89mm wide and 141mm tall, it’s very compact, taking up only a fraction of precious desktop real estate. It also looks fantastic – sleek and stylish, with clean lines and a modern aesthetic. Hard-wearing steel and reinforced nylon resin construction ensure the NT-USB Mini is ready to take on the rigours of recording anywhere and everywhere.
LOGILINK HS0047 - Microphone, 3.5-mm jack, flexible
16.1 EUR
Microphone with stand and flexible neck- Connection: 3.5-mm stereo jack
- With on/off switch and detachable foam wind muff
- Gooseneck for easy alignment of the microphone
- Base: Dia. 9 x 7 mm
- Sensitivity: -58 ±3 dB
- Impedance: 2.2 k Ohm
- Frequency response: 100 - 16,000 Hz
- SNR: more than 60 dB
- Supports: Windows 98SE/ME/2000/XP/2003/Vista/7/8/10 and Mac OS 8.6 or higher
- Cable length: 1.80 m
The HS0047 has a fully flexible neck and can therefore adapt to any angle you like.
DELOCK 66300 - USB Condenser Microphone Set
76.05 EUR
This professional USB condenser microphone by Delock can be used for high-quality voice and vocal recordings.Optimal recordings
The microphone has a 16 mm condenser and a cardioid polar pattern (unidirectional) and therefore ideally captures the sound. Due to high power, low self-noise and precise performance, even the finest sounds are recorded crystal clear.
Dual Layer Pop Filter & Windscreen
Due to the included dual layer pop filter and the windscreen, the recording quality is further optimized. Annoying wind noises are optimally filtered.
High sampling rate
Typical USB microphones work with 16 Bit and 44 KHz. The Delock microphone offers a sampling rate of 24 Bit and 192 kHz, so it is possible to record in Hi-Fi studio quality.
Plug & Play
Due to USB Plug & Play the microphone is ready to use immediately, no driver installation is needed. The microphone works with all common operating systems such as Windows, Mac OS, Chrome OS and Linux.
Stable & adjustable stand
The stand ensures that the microphone is stable on the table. With the telescopic function, the microphone can be adjusted to the preferred height.
Specification
- Connector: 1 x USB 2.0 Type-B female
- Directivity: unidirectional
- Sensitivity: -38 dB +/- 3 dB
- Frequency range: 30 Hz - 16 kHz
- Sample rate: 24 Bit / 192 kHz
- Signal-to-noise ratio (SNR): ca. 70 dB
- Self-Noise: max. 16 dBA
- Sound pressure level (SPL): max. 120 dB
- Dual-Layer pop filter: Ø 120 mm
- Stand: Ø ca. 130 mm (ca. 600 g)
- USB bus powered
- Plug & Play
System requirements
- Chrome OS
- Linux Kernel 4.4 or above
- Mac OS 10.9 or above
- Windows 7/7-64/8.1/8.1-64/10/10-64
- PC or laptop with a free USB Type-A port
Package content
- USB microphone
- USB 2.0 Type-A to USB 2.0 Type-B cable, length ca. 2.5 m
- Shock mount (spider)
- Telescopic rod
- Stand
- Pop filter
- Windscreen
- User manual
DELOCK 66882 - Professional USB Condenser Microphone 24 Bit / 192 kHz
51.24 EUR
This professional USB condenser microphone by Delock can be used for high-quality voice and vocal recording, making it suitable for streaming, podcasting, gaming and video meetings.Optimal recordings
The microphone has a 16 mm c
THRONMAX M4 - Microphone, MDrill Zero, 48 kHz, black
66.75 EUR
The MDrill Zero not only stands out thanks to its appearance, it also has a lot of technical features on offer. Whether for streamers, gamers or musicians, the M4 with its 2 capacitor capsules and 2 recording patterns offers everything to ensure that your recordings get a particularly clear and full sound. For easy and uncomplicated handling, the MDrill Zero has a knob for volume and directivity characteristics and can be mounted on almost all standard microphone stands thanks to its microphone holder with universal thread.- HD, studio-quality recordings.
- Patented Vertigain technology. Recorded sounds are up to 10% clearer than with conventional microphones
- Colour: black
- Sample rate: 48 kHz, 16 bit recording
- Frequency: 20 Hz - 20 kHz
- 2 directivity characteristics: kidney-shaped (for streaming and for gamers), 360° omnidirectional (conference calls and events)
- Port 1: 3.5 mm aux-in
- Port 2: USB-C (including 2m braided USB-C cable)
- 2x capacitor capsules (16 mm and 10 mm)
- RGB LED indicator light for mode display
- Mute button
- With universal thread for microphone shock mounts, microphone stands, tripods etc.
- Perfect for YouTubers, broadcasters and gamers
THRONMAX M20KIT - Microphone, USB Streaming Kit
77.08 EUR
- Streaming kit contains: RGB microphone, spring boom arm and desk clamp, 5/8'' & 3/8'' thread, tripod adapter, M20 sponge, pop filter, braided USB cable
- Condenser microphone (cardioid mic)
- Professional sound chipset 96 kHz/24 bit, high-resolution sampling rate
- USB 2.0 data port (USB-C)
- USB cable double shielded, reduces interference
- Suitable for gaming recordings, PC karaoke, video calls, podcasts, live streaming, etc.
- Cable length: 2 m
- 24 modes RGB-LED
With this kit you are perfectly equipped for gaming recordings, PC karaoke, video calls, etc. This condenser microphone was developed with a professional sound chipset that allows a high resolution sampling rate. It has an USB 2.0 port (USB-C) which can be easily connected to your computer or Mac OS. With the pop filter and foam windscreen, the condenser microphone records your voice crystal clear and thanks to the shock mount the microphone lies firmly and protected in the boom arm.
RØDE RODE WIMICROC - Microphone system for smartphones, USB-C, black
194.97 EUR
- Wireless microphone system for smartphones
- Ultra-compact complete system including charging case
- Simple operation - plug and play
- The two wireless microphones can be clipped on, alternatively they can be attached using magnets. Wind protection built into the microphone
- GainAssist automatic level adjustment
- Crystal-clear audio quality
- Receiver module with integrated USB-C plug
- Modules pair automatically
- Range: 100 m
- Battery life: 7 hours (21 hours with charging case)
- Charging time: three hours
System requirements:
- Android 11, iOS 14 or newer
- USB-C port
Specifications
- Dimensions of transmitter: 40 x 20 x 17 mm
- Weight of transmitter: 12 g
- Dimensions of receiver: 44 x 24 x 9 mm
- Weight of receiver: 6 g
- Dimensions of charging case: 72 x 58 x 30 mm
- Weight of charging case: 61 g
- Incl. two additional miniature furry wind protection sleeves that can be fitted to the microphone
- Incl. 2x magnetic fastenings for the transmitter modules
- Incl. USB-C to USB-C cable
THRONMAX NEWM9 - Microphone, Fireball, 48 kHz/16 bit
40.91 EUR
- 14 mm condenser capsule offers crystal clear audio for Skype, Youtube and others
- Record vocals create podcasts, and add narration to your home movies
- Sampling rate: 48 kHz, 16 bit recording
- Plug-and-play – no driver installation needed
- USB 2.0 device (USB 3.0 compatible as per USB 3.0 backward compatibility specification)
- Fast and easy recording
- Compatible with Windows 10, Windows 8 (including 8.1), Windows 7, Windows Vista, Windows XP (Home and Professional), and Mac OS X (10.4.11 or higher), and requires a minimum of 64 MB of RAM
- Cable length: 1.8 m
- Color: Black
With Thronmax Fireball, quick and easy recording is finally a reality. Simply mount Fireball on the included sticky pad stand, plug the USB cable into your Mac or PC and that’s it. You’re ready to sit back and start recording crystal-clear audio for any recording or live streaming.
RPI HB DAC2 PROX - Raspberry Pi Shield - HiFiBerry DAC2 Pro XLR
87.78 EUR
HiFiBerry DAC2 Pro XLRThe HiFiBerry DAC2 Pro is a high-resolution digital-to-analog and analog-to-digital converter for the Raspberry Pi (newer models with 40-pin GPIO connector). This is a dedicated sound card for the Raspberry Pi, optimized for a specific use case: affordable and high quality audio playback.
Unlike the DAC2 Pro, this variant offers two XLR connectors to connect even high quality audio equipment to a Raspberry Pi.
Technical Details
• stereo output
• can be equipped with an additional digital signal processor (DSP) for flexible audio processing
• dedicated 192kHz/24bit high quality Burr-Brown DAC
• hardware volume control for DAC (supports ALSA mixer controls)
• connects directly to the Raspberry Pi, no additional cables needed
• compatible with all Raspberry Pi models with a 40-pin GPIO connector
• direct power supply via the Raspberry Pi, no additional power needed
• dual linear voltage regulators with ultra-low noise for optimal audio performance
• low jitter dual domain clock for optimized clock decoupling from the Raspberry Pi
• HAT compliant, EEPROM for automatic configuration
• gold-plated RCA output connectors
• comes with all components required for mounting, including spacers
Delivery without Raspberry Pi and DSP module (see ''Accessories and Alternative Products'')
Microphones REICHELT IE Best Products
FREI ARD MIC MODUL5 - Arduino - Microphone module, LM386, analog
13.04 EUR
Sound Sensor Module Audio detection module with LM386 amplifier chipThe sound sensor module is used to detect sounds and is based on the LM386 audio amplifier chip. It amplifies the sound signals detected by the microphone and outputs analog voltage values that can be processed by microcontrollers such as Arduino. The module is ideal for simple noise detection and sound evaluation projects.
- Sensitive microphone input Picks up sound signals from the environment and converts them into electrical signals.
- Integrated LM386 amplifier Amplifies weak input signals for a stable analog output.
- Adjustable sensitivity The noise detection threshold can be adjusted via a potentiometer.
- Compatible with Arduino Direct connection via VCC, GND and A0 possible, easy integration into microcontroller projects.
- Simple wiring Only three wires required, quick commissioning for learning and DIY projects.
Technical data:
- Operating voltage: 5 V DC
- Signal output: analog (OUT)
- Amplifier chip: LM386
- Connection: 3-pin (VCC, GND, OUT)
- Microphone type: Electret condenser microphone
- Compatibility: Arduino, ESP32, Raspberry Pi and others
- Dimensions: approx. 35 × 16 × 8 mm
Areas of application:
- Sound-activated controls
- Light or motor activation for sound events
- Environmental and noise monitoring
- Acoustic detection in learning and electronics projects
- Sound level demonstrations in the education sector
The Sound Sensor Module is a simple, effective solution for sound detection and ideal for beginners in electronics and Arduino projects.
FREI ARD MIC MODUL1 - Arduino - Microphone module, analog
13.15 EUR
The sound detector is based on a microphone and a power amplifier and can be used to detect the sound level in the environment. The sensor receives the signal through both a digital and an analog output.The sensitivity can be adjusted with the potentiometer and the LEDs mounted on the PCB indicate the power and the compressor output.
LOGILINK HS0058 - Microphone, USB-C, with RGB lighting
51.24 EUR
Microphone, cardioid, NRC, 192 kHz at 24 bits, RGB lighting, streaming, podcast, studio- Studio-quality HD recording perfect for YouTube, broadcasters and gamers
- Sample rate: 192 kHz at 24 bits
- Frequency: 20 Hz - 20 kHz
- Directional characteristic: cardioid - prioritises sound sources directly in front of the microphone
- Connection 1: 3.5-mm jack for monitor headphones
- Connection 2: USB-C (including 1.5-m USB-A to USB-C cable)
- With volume/noise reduction control and mute button
- With 3/8'' threaded hole for microphone shock mounts, microphone stands, tripods etc.
- Dynamic RGB lighting
- Supported operating systems: Windows, MacOS, Android, iOS
- Colour: black
Product information from LogiLink
Level up your setup with the LogiLink HS0058 USB microphone. With 24-bit recording and a sample rate of 192 kHz, this condenser microphone delivers clear, immersive sound that captures every nuance - perfect for streaming, gaming and voice chats. Thanks to its compatibility with major platforms, it is the ideal choice for podcasters, musicians (e.g. for recording vocals or acoustic instruments) and anyone who needs clear voice recordings.
LOGILINK HS0059 - Microphone, USB-C, with RGB lighting
66.75 EUR
Microphone, cardioid/omnidirectional, NRC, 192 kHz at 24 bits, RGB lighting, streaming, podcast, studio- Studio-quality HD recording perfect for YouTube, broadcasters and gamers
- Sample rate: 192 kHz at 24 bits
- Frequency: 20 Hz - 20 kHz
- Directional characteristics: cardioid and 360° omnidirectional
- Connection 1: 3.5-mm jack for monitor headphones
- Connection 2: USB-C (including 1.5-m USB-A to USB-C cable)
- With volume/noise reduction control and mute button
- With 3/8'' threaded hole for microphone shock mounts, microphone stands, tripods etc.
- Dynamic RGB lighting
- Supported operating systems: Windows, MacOS, Android, iOS
- Colour: black
Product information from LogiLink
Enjoy professional studio quality with the flexibility for any scenario. The LogiLink HS0059 USB condenser microphone delivers an ultra-high sample rate of 192 kHz at 24 bits, making it perfect for any application. Use cardioid pickup for solo speakers, streaming, gaming and voice chats, or switch to omnidirectional pickup for group interviews and meetings.
RPI HB MINI AMP - HiFiBerry MiniAMP, Raspberry Pi Shield
34.45 EUR
HiFiBerry MiniAmpThe HiFiBerry MiniAmp is a tiny, highly efficient Class-D power amplifier for the Raspberry Pi Zero (but works also on all newer models with 40 pin GPIO connector). The speakers just have to be connected directly to the board, which makes it an ideal module for low-profile applications where the power of our Amp+ is not needed.
Facts
• Up to 2x3W output power
• Capable of driving a pair of 4-8 Ohm speakers
• 44.1kHz - 192kHz sample rates
• Digital-analog conversion included, no need for external DACs or sound cards
• Connects directly to the Raspberry Pi A+/B+/2B/3B/Zero, no additional cables needed
• Directly powered from the Raspberry Pi, no larger power supply needed
• Comes as a pre-fabricated kit. You just plug it onto the Raspberry Pi. On the Raspberry Pi Zero, you have to solder the GPIO header onto it.
• Low-noise voltage regulator for optimal audio performance
• Comes without any mounting material (spacer, 40-pin header for the Raspberry Pi Zero).
• Does not feature hardware volume control – however most programs feature software volume control.
Dimensions 3.0 x 6.5 x 1cm
Note
Delivery without spacer
Usage recommendations
• very small audio playback devices
HIFIBERRY RPI HB BEOCREATE - Raspberry Pi Shield - Beocreate 4 Channel Amplifier
242.46 EUR
The Beocreate 4 channel amplifier is a very flexible DSP/DAC/amplifier combination board designed for high-quality music playback in combination with passive loudspeakers.- Up to 180W output power (2x30W, 2x60W)
- Capable of driving up to four of 4-8 Ohm speakers (the two 60W channels can drive 2 Ohm speakers)
- Fully controllable from the Raspberry Pi
- sample rates up to 192kHz
- 4 channel digital-analog conversion included
- Connects directly to the Raspberry Pi A+/B+/2B/3B/Zero, no additional cables needed
- Only one 12-24V external power supply needed to power both the Beocreate board and a Raspberry Pi, no need for an externalUSB power supply
- No soldering required, the Raspberry Pi can be plugged easily onto the Beocreate board. Speakers can be connected via screw terminals
- Can work standalone (without the Raspberry Pi) as a digital amplifier. However, to program the DSP, a Raspberry Pi is required
Software:
https://www.hifiberry.com/beocreate/
IDUINO ARD MIC MODUL2 - Arduino - Microphone module, analog
12.01 EUR
Small microphone module for Arduino, analogueSpecification
• power supply: 5 V / 3.3 V
• analog output
• high sensitivity microphone
• power indicator light
• frequency response range: 50 Hz - 20 KHz
• impedance: 2.2 kOhm
• Sensitivity: 48 - 66 dB
• Polar pattern: universal
• Operating temperature: -40 ... +85 C
• Operating humidity: 30 - 90%.
• Hole for mounting screw 3 mm.
• dimensions (L x W x H): 40 x 15 x 10 mm
IDUINO ARD MIC MODUL4 - Arduino - Microphone module, analog
12.01 EUR
Large microphone moduleThis is a highly sensitive sound detection module with two output signal pins.
D0: When it detects a sound up to a certain threshold, it can output a high or low level.
A0: It can output the output voltage signal of the microphone in real time.
RPI HB DSP - Raspberry Pi Shield - HiFiBerry DSP Add-On Board
108.09 EUR
The HiFiBerry DSP add-on card is a card that can be used to expand some HiFiBerry cards with a digital signal processor for audio processing. The DSP can be programmed via Analog's Sigma Studio or used with predefined DSP programs.Technical data
• 300 MHz digital signal processor (6144 instructions per sample including FFT and FIR accelerators)
• high-quality asynchronous sample rate converter that can upsample/downsample/mix audio sources
• Users can upload programs developed with Analog's SigmaStudio
• connects to the DSP header of selected HiFiBerry sound cards (see accessories)
• no soldering, delivered as a pre-fabricated kit
• powered directly from the Raspberry Pi, no additional power supply required
Note that the actual board may look slightly different. Layout and components are subject to change without notice. We do not guarantee a specific board layout or components!
Further information is available at
https://www.hifiberry.com/docs/data-sheets/dsp-addon/
RØDE RODE VMGO - Directional on-camera condenser microphone
87.37 EUR
Directional on-camera condenser microphone- Plug & play - without battery (requires plug-in power from camera)
- 1/2'' condenser capsule
- Polar pattern: supercardioid
- Microphone angle: approx. 45°
- Robust ABS housing
- Lyre® shock mount by Rycote®
- Standard hot shoe adapter
At 18 cm long, the VideoMic GO is an easy-to-use mono on-camera microphone that can be used to enhance the sound quality of video soundtracks considerably. It can be pushed on to the hot shoe of the camera in the blink of an eye, secured using the included spiral cable and is then ready for use straight away - no switch, no settings, no battery and conveniently lightweight at just 73 g!
The red Rycote double ''Lyre'', a special thermoplastic shock mount, ensures optimum decoupling of the VideoMic GO from the camera. This prevents structure-borne noise or handling noises from being picked up by the sensitive 1/2'' condenser capsule of the microphone. The VideoMic Go can also be operated separately from the camera on a stand, with a handle or a boom. There is a 3/8'' thread in the base of the bracket for this purpose.
DELOCK 65939 - Microphone, USB, Table Stand
32.64 EUR
This professional USB microphone by Delock can be used for high-quality speech and voice transmissions. The microphone has a circle pattern (omnidirectional) and therefore captures the acoustic signal ideally. Due to a high power, low self-noise and precise performance, even the finest sounds are optimally recorded. The table stand can be folded and transported easily if required.Specification
- Connector: 1 x USB 2.0 Type-A male
- Directivity: omnidirectional
- Sensitivity: -38 dB +/- 3 dB
- Frequency range: 50 Hz - 16 kHz
- Sample rate: 16 Bit / 44.1 kHz
- Signal-to-noise ratio (SNR): ca. 36 dB
- Impedance: 2.2 kOhm
- Cable length: ca. 1.35 m
- Dimensions (LxWxH): ca. 150 x 55 x 30 mm
- USB bus powered
- Plug & Play
System requirements
- Chrome OS
- Linux Kernel 2.6 or above
- Mac OS 10.9 or above
- Windows 7/7-64/8.1/8.1-64/10/10-64
- PC or laptop with a free USB Type-A port
Package content
- USB microphone
- Table stand
- User manual
Package
- Retail Box
SEEED RPI RESP 2MIC - ReSpeaker 2-Mic HAT for Raspberry Pi
26.8 EUR
The ReSpeaker 2-Mics Pi HAT is an expansion board for Raspberry Pi with two microphones designed for AI and voice applications. It can be used to create more powerful and flexible voice products with integration of Amazon Alexa Voice Service, Google Assistant, etc. The board was developed based on the WM8960 stereo codec with low power consumption.• two microphones
• 2 Grove interfaces with support for GPIO and I2C
• programmable button and LED: one button and three LEDs
Delivery without Raspberry Pi
Further information about the board as well as data sheets, instructions and downloads can be found at https://wiki.seeedstudio.com/ReSpeaker_2_Mics_Pi_HAT/
Instructions in pdf format are available for Grove users (especially beginners). Before using the product, you should definitely read the chapters ''Preface'', ''Getting Started'' and ''Introduction to Grove''!
RPI HB DIGI2 PRO - Raspberry Pi Shield - HiFiBerry Digi2 pro
73.83 EUR
HiFiBerry Digi2 ProThe HiFiBerry Digi2 Pro Shield is a high-resolution SPDIF interface for the Raspberry Pi - affordable, high-quality audio playback.
Features
• SPDIF output 2-channel
• can be equipped with an additional digital signal processor (DSP) for flexible audio processing
• no volume control or sound control, only digital audio when sent by the application (''bit-perfect'')
• output isolation transformer
• connects directly to the Raspberry Pi, no additional cables are required
• compatible with all Raspberry Pi models with a 40-pin GPIO connector
• powered directly from the Raspberry Pi, no additional power supply required
• low-noise linear voltage regulator
• dual-domain clock with low jitter for optimized clock decoupling from the Raspberry Pi
• EEPROM for automatic configuration
Scope of delivery
• HiFiBerry Digi2 Pro sound card
• 4x M2.5 x 12 mm spacers
Please note
Current stock version 2.2
RPI HB DAC2 ADCP - Raspberry Pi Shield - HiFiBerry DAC2 ADC Pro
95.95 EUR
The HiFiBerry DAC2 ADC Pro is a high-quality sound card for the Raspberry Pi that enables both digital-to-analog and analog-to-digital conversion. With support for sample rates up to 192 kHz at 24-bit, this module is ideal for applications that require both audio playback and recording. The combination of Burr-Brown DAC and ADC ensures excellent audio quality, while the direct connection to the Raspberry Pi allows for easy integration.- Compatibility: All Raspberry Pi models with 40-pin GPIO
- DAC: Burr-Brown PCM5122, 192 kHz / 24 bit
- ADC: Burr-Brown PCM1863, 192 kHz / 24 bit
- Maximum input voltage: 2.1 Vrms (unbalanced), 4.2 Vrms (balanced)
- maximum output voltage: 2.1 Vrms
- Signal-to-noise ratio (ADC): 110 dB typical
- Signal-to-noise ratio (DAC): 112 dB typical
- THD+N (ADC): -90 dB typical
- THD+N (DAC): -93 dB typical
- Frequency response: 10 Hz - 70 kHz (-3 dB)
- Input gain: -12 dB to +32 dB
- Power consumption: < 0.3 W
- Supported sample rates: 44.1 - 192 kHz
- Power supply: Directly via the Raspberry Pi
- Dimensions (LxWxH): 5.5 × 6.5 × 2.5 cm
The module has gold-plated RCA outputs for high-quality signal transmission and offers both balanced and unbalanced inputs via a 6-pin connector. A microphone bias can be activated to support electret microphones. Configuration is easily done via the file `config.txt` with the overlay `dtoverlay=hifiberry-dacplusadcpro`.
Scope of delivery
- HiFiBerry DAC2 ADC Pro
- 4x M2.5x12mm spacers
An ideal module for anyone looking for a professional audio solution with recording and playback functionality for the Raspberry Pi.
External links
https://www.hifiberry.com/docs/data-sheets/datasheet-dac2-adc-pro/
https://www.hifiberry.com/wp-content/uploads/2019/07/hifiberry-dac-plus-adc-1.2.step.zip
RPI HB AMP4 PRO - Raspberry Pi Shield - HiFiBerry AMP4 Pro
95.95 EUR
The HiFiBerry Amp4 Pro is a high-quality, efficient Class-D stereo amplifier for the Raspberry Pi and the extended version of the Amp4. Equipped with integrated dual-domain clocks, it offers even more precise audio processing. In combination with a Raspberry Pi, it creates a powerful, compact audio system - simply connect speakers and get started.- Amplifier: Class-D stereo amplifier
- Power: Up to 60W (30W per channel)
- Power supply: 12-24V DC via Amp4 Pro (also powers the Raspberry Pi)
- recommended voltage: 12-20V for 4 Ohm speakers, 20V for 8 Ohm speakers
- compatible speakers: 4-8 Ohm impedance
- Sample rates: 44.1 - 192 kHz
- Audio resolution: 16-32 bit
- Dual domain clocks: Yes, for more precise audio processing
- Compatibility: All Raspberry Pi models including Pi 4 and Pi 5
- Driver compatibility: Uses DAC+ driver
- Expandable: Support for DSP expansion module
The Amp4 Pro not only reliably powers the Raspberry Pi, but also additional 5V consumers such as the official 7'' Raspberry Pi display or other hardware thanks to the improved voltage regulator. External 5V power supplies are no longer necessary.
A compact, powerful audio system with enhanced precision - ideal for demanding music lovers, audio projects and embedded applications with the Raspberry Pi.
RPI HB DAC2 PRO - Raspberry Pi Shield - HiFiBerry DAC2 Pro
60.18 EUR
HiFiBerry DAC2 ProThe HiFiBerry DAC2 Pro is a high-resolution digital-to-analog and analog-to-digital converter for the Raspberry Pi (newer models with 40-pin GPIO connector). This is a special sound card for the Raspberry Pi, optimized for a special application: affordable and high quality audio reproduction.
Technical details
• Stereo output
• integrated headphone amplifier
• can be equipped with an additional digital signal processor (DSP) for flexible audio processing
• dedicated 192kHz/24bit Burr-Brown DAC with high quality
• Hardware volume control for DAC (supports ALSA mixer controls)
• connects directly to the Raspberry Pi, no additional cables needed
• compatible with all Raspberry Pi models with a 40-pin GPIO connector
• direct power supply via the Raspberry Pi, no additional power needed
• Two ultra-low noise linear voltage regulators for optimal audio performance
• low-jitter dual-domain clock for optimized clock decoupling from the Raspberry Pi
• HAT compliant, EEPROM for automatic configuration
• gold plated RCA output connectors
• is supplied with all the components required for assembly, including spacers
• Audio connector for connecting an analog audio amplifier
Delivery without Raspberry Pi
RPI IQ CODECZERO - Raspberry Pi Shield - IQaudio Codec Zero
33.93 EUR
IQaudio Codec Zero is a Raspberry Pi zero-size audio I/O HAT. It provides bidirectional digital audio (I2S) between Raspberry Pi Zero and its integrated Dialog Semiconductor DA7212 codec. Codec Zero supports a range of input and output devices, from built-in MEMS microphones to external monoelectret microphones to 1.2 W and 8 ohm mono speakers.The IQaudio Codec Zero has green and red LEDs that can be used for status, as well as a tactile button that can be used to start an event. Codec Zero is a good starting point for a walkie-talkie, smart doorbell, vintage radio hack or smart speaker.
Note
• see datasheets for more useful installation information.
LOGITECH GEM - Logitech Group expansion microphones
306.69 EUR
Extend the talk range from 6 m (20 ft) to 8.5 m (28 ft) to clearly hear people further away from the hands-free device. Microphones (in pairs) are automatically detected and configured by simply connecting them to the hands-free device.
RPI HB AMP4 - Raspberry Pi Shield - HiFiBerry AMP4
82.25 EUR
The HiFiBerry Amp4 is a high-quality, efficient Class-D stereo amplifier for the Raspberry Pi. Plugged directly into the Raspberry Pi, it transforms it into a powerful audio system. All you need to do is connect a pair of speakers. The power supply is provided by a single 12-24V power source, which supplies both the Raspberry Pi and the amplifier.- Amplifier: Class-D stereo amplifier
- Power: Up to 60W (30W per channel)
- Power supply: 12-24V DC via Amp4 (also supplies the Raspberry Pi)
- recommended voltage: 12-20V for 4 Ohm speakers, 20V for 8 Ohm speakers
- compatible speakers: 4-8 Ohm impedance
- Sample rates: 44.1 - 192 kHz
- Audio resolution: 16-32 bit
- Compatibility: All Raspberry Pi models, including Raspberry Pi 4
- Driver compatibility: Uses DAC+ driver
- Expandable: Support for DSP expansion module
The Amp4's integrated voltage converter is powerful enough to power the Raspberry Pi itself. An additional 5V power supply is not necessary. The amplifier is not designed to supply power-intensive USB devices with continuous power. However, devices with low power consumption such as keyboards or mice are not a problem.
A practical solution for high-quality audio applications with the Raspberry Pi - space-saving, powerful and easy to install. Ideal for speaker projects in the DIY or embedded sector.
RPI HB AAMP60 - Raspberry Pi Shield - HiFiBerry AAmp60
73.1 EUR
The HiFiBerry AAmp is a high quality, high efficiency Class D power amplifier add-on for some HiFiBerry DAC sound cards.The AAmp is an analog amplifier add-on for some HiFiBerry cards. It connects to your HiFiBerry DAC card and adds a 60W analog amplifier. A 12-20V power supply is used to power not only the amplifier, but also the DAC and the Raspberry Pi.
You can use it with the following HiFiBerry cards that come with the required analog output connector:
DAC2 HD (Part No: RPI HB DAC2 HD).
DAC + ADC (item no.: RPI HB DAC+ ADC)
DAC + ADC Pro (item no. RPI HB DAC+ ADCP)
• Dimensions (LxWxH): 9 x 6 x 3 cm
• Power connector DC jack hollow plug (Ø5.5 x Ø2.1 mm)
Note
This is not a HAT that can be used with the Raspberry Pi standalone! It does not connect directly to the Raspberry Pi, but requires an additional supported HiFiBerry DAC card.
RPI HB DAC8X - Raspberry Pi Shield - HiFiBerry DAC8X
77.03 EUR
This 8-channel DAC board is designed specifically for the Raspberry Pi 5 and provides high quality, unbalanced audio output via four 3.5mm stereo jacks. It is ideal for applications such as active speaker systems or surround sound projects where multiple audio channels are required. Thanks to its compact HAT design, it can be mounted directly on the Raspberry Pi 5.- Outputs: 8-channel unbalanced (via 4× 3.5 mm stereo jack)
- Compatibility: Only with Raspberry Pi 5
- Form factor: Compact HAT
- Maximum output voltage: 2 Vrms
- Signal-to-noise ratio: 112 dB
- THD+N: -93 dB
- Sampling rates: 44.1 - 192 kHz
- Interfaces:
- 4× 3.5 mm stereo jack sockets
- 40-pin GPIO connector
- Power supply: via 5 V GPIO from Raspberry Pi 5
- Dimensions (LxWxH): 55 × 65 × 25 mm
This board is the perfect choice for anyone who wants to integrate multi-channel audio playback with excellent sound quality into their Raspberry Pi 5 projects - whether for music, home theater or professional applications.