Review Iwh vertriebs gmbh iwh 075900 automatic charger for lead bat

IWH VERTRIEBS GMBH GARAGE 20990 - Garage - oil filter wrench, fabric tape 15.74 EUR Oil filter ransom wrench ''Textile

Specifications

• suitable for all spin-on filters with a diameter from 4 to 14 cm
• design: with textile webbing: 45 cm length

SEE OFFER SEE OFFER ebay

IWH VERTRIEBS GMBH GARAGE 20994 - Garage - oil filter wrench, steel band 14.55 EUR Oil filter - loosening wrench ''Profi

Specifications

• suitable for all spin-on filters
• for diameters from 6 to 11 cm
• suitable also for inaccessible places
• with adjusting screw and special loop
• with steel strap

SEE OFFER SEE OFFER ebay

IWH VERTRIEBS GMBH GARAGE 20876 - Garage - Spark plug wrench, 16mm, double joint 13.46 EUR Spark plug wrench, 16mm, double joint

Specifications

• made of special steel
• double joint with great leverage
• handle plastic coated

SEE OFFER SEE OFFER ebay

IWH VERTRIEBS GMBH GARAGE 20877 - Garage - spark plug wrench, 22mm, double joint 13.83 EUR Spark plug wrench, 22 mm, double joint

Specifications

• made of special steel
• double joint with great leverage
• handle plastic coated

SEE OFFER SEE OFFER ebay

EINHELL 1002275 - Automatic charger for lead-acid batteries, 12/ 24 V. 214.6 EUR The Einbright Battery Charger CE-BC 30 M is an intelligent battery charger adapted to the technically advanced and low-noise batteries of modern vehicles. The intelligent battery charger with microprocessor control is suitable for a wide range of battery types in vehicles and has a range of technical protection and care mechanisms. The main focus of the development was on a fast, gentle charging of the batteries, so that the longest possible service life at full power is achieved. The operation of the charger is easier than with conventional devices thanks to a detailed charging display. The single-light all-rounder is suitable for gel batteries, AGM, as well as maintenance-free and low-maintenance lead acid batteries. The CE-BC 30 M is suitable for 12V and 24V batteries. The multi-stage charging cycle of the Einbright battery charger is automatically monitored and adjusted by the microprocessor control. The maintenance charge relieves the battery cells and prolongs the service life, thus preventing an avoidable, costly replacement of a defective vehicle battery. Cars, motorcycles or scooters are ready for use at the start of the season. The Einbright battery charger can support the battery with 100 a starting current (max. 5 seconds) by means of an external start function.

Intelligent battery charger with microprocessor control
Multi-stage charging cycle, microprocessor controlled and monitored
2 in 1: Charge and power off with one device
Selectable voltage 12 V/24 V for adaptation to vehicle battery
Maintenance charging function for a permanent, ideal charge state
All-round battery charger for a wide range of battery types
For gel, AGM, maintenance-free and low-maintenance lead-acid batteries
Use extends battery life
LED battery voltage and charge progress indicator
Electronic overload, short circuit and reverse polarity protection
Fully Insulated Battery Terminals

Technical Data:
Power supply: 230 V/ 50 Hz
Charging voltage: 12/ 24 V.
Starting aid: 100 a - 5 sec.
Charging Current Min./ Max. (12 V): 3/ 30 A.
Charging Current Min./ Max. (24 V): 4/ 15 A.

SEE OFFER SEE OFFER ebay

H-TRONIC AL 300 PRO - Automatic charger for 2 V, 6 V and 12 V lead-acid batteries 24.37 EUR Automatic charger for 2 V, 6 V and 12 V lead and lead gel batteries

As soon as the battery's final charge voltage is reached, the electronic controller automatically reduces the charging current. This protects the battery from damage. A charge control and polarity display provide information about the correct operating status. Ideally suited for vehicles, boats, caravans, motorcycles and devices that remain unused for long periods of time.

• Incl. battery terminals
• Protection against short circuit and reverse polarity
• Final charge voltages: 2.3/6.9/13.9 V
• Charging current: max. 300 mA

SEE OFFER SEE OFFER ebay

IWH VERTRIEBS GMBH GARAGE 10870 - Garage - cross key / wheel cross / turnstile 18.37 EUR Cross key silver

Specifications

• sizes: 17 x 19 x 13/16'' x 22 mm
• corresponds to DIN 899
• material: special steel

SEE OFFER SEE OFFER ebay

H-TRONIC AL 600 PLUS - Lead-acid battery charger with diagnostic function 38.84 EUR Charger for 2 V, 6 V and 12 V lead-acid batteries (acid, gel, AGM)

• Max. charging current of 0.6 A (automatic adjustment)
• Multi-phase Vu charging characteristic curve, I phase, U1 phase, U2 phase
• Software-controlled battery test function and defect detection before the start of the charging process
• Automatic battery maintenance mode (battery refreshing after charging)
• Trickle charge — the battery can remain permanently connected
• Protection against reverse polarity, short-circuit and overcharging

SEE OFFER SEE OFFER ebay

ANSMANN ANS BC 6-12V-1A - Automatic charger for lead-acid batteries, IP65, 6 - 12 V/1 A 49.18 EUR 5-stage car charger with automatic voltage detection for 6-V and 12-V lead-acid, lead-gel and AGM batteries

Intelligent and safe charging control
Thanks to its wide range of features, the 5-stage charger BC 6 - 12 V/1 A ensures safe, battery-preserving charging of lead-acid batteries with a capacity of 4 - 30 Ah. It guarantees optimum performance and a long battery service life.

The charger is dustproof and protected against splash water (IP65) and has the following electrical safety features: reverse polarity protection, overcharge protection, deep discharge protection and short-circuit protection

In addition, the intelligent charger is suitable for standby/parallel operation and can remain connected to the battery at all times. It always keeps it fully charged, even if the battery is under load/discharging at the same time.

When the battery is connected, the charger automatically detects the battery voltage (6 V or 12 V). The LED indicator flashes green during charging and is solid green when the battery is fully charged.

Fully automatic, intelligent five-stage charging

SEE OFFER SEE OFFER ebay

ANSMANN ANS BC 6-12V-4A - Automatic charger for lead-acid and lithium batteries, IP65, 6 - 68.76 EUR 10-stage car charger for 6-V and 12-V lead-acid, lead-gel and AGM batteries, as well as 12-V LiFePO4 batteries

Intelligent and safe charging control even under frosty conditions with deep discharge protection.
Thanks to its wide range of features, the 10-stage charger BC 6 - 12 V/4 A ensures safe, battery-preserving charging of lead-acid batteries with a capacity of 4 - 120 Ah. It guarantees optimum performance and a long battery service life. The ''MODE'' button can be used to select 6 intelligent charging programs or a power supply mode that can be used to operate 12-V devices such as a cool box.

The charger is dustproof and protected against splash water (IP65) and has the following electrical safety features: reverse polarity protection, overcharge protection, deep discharge protection and short-circuit protection

In addition, the intelligent charger is suitable for standby/parallel operation and can remain connected to the battery at all times. It always keeps it fully charged, even if the battery is under load/discharging at the same time.

Fully automatic, intelligent ten-stage charging

SEE OFFER SEE OFFER ebay

VICTRON ENERGY VE BS IP22 12/15 - Automatic charger for lead, lithium batteries, IP22, 12V/15A 149.48 EUR The Blue Smart IP22 charger from Victron Energy, is a professional, compact 12 V 15 a battery charger of the latest generation with 3 charging outputs and built-in Bluetooth! The charger can be used with equipment in your workshop or with motor vehicles such as (classic) cars, motorcycles, boats and mobile homes and charges both classic 12 V lead-acid batteries and modern lithium batteries

Technical Highlights:

Charges 12 V lead-acid, gel, AGM and lithium batteries
15 a maximum charging current
3 Battery Charging Outputs
State-of-the-art, seven-stage charging algorithm
With integrated Bluetooth for use with the free VictorConnect app

Intelligent charging, up to the perfect battery condition
The seven-stage charging algorithm gets the most out of your battery. The charger provides the battery with the energy it needs, keeps it in a healthy state, ensures better performance... and a longer life.

Recovery of deep-discharged ''dead'' batteries
Unlike most other brands and product lines, the Blue Smart IP22 charger will try to recharge a low-discharge battery by forcing it to have a low-charge current. Normal charging will then resume as soon as there is sufficient voltage between the battery terminals.

Remotely check battery status using the VictorConnect app
The Blue Smart charger has built-in Bluetooth. This allows you to check the status of the charger and battery on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictorConnect app.

Trend-setting efficiency
With an efficiency of up to 94%, these chargers generate up to four times less heat compared to the industry standard. After the battery has also been fully charged, the power consumption drops to less than 0.5 watts, which is about five to ten times better than the industry standard.

Storage mode: Less maintenance and aging when the battery is at rest
Storage mode is activated whenever no discharge has occurred within 24 hours. The charge maintenance voltage is then reduced to 2.2 V/cell (13.2 V for a 12 V battery) to minimize the gas development and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gas voltage. This provides a kind of equalizing charge that prevents electrolyte stratification and sulphation, the two main causes of premature battery failure.

SEE OFFER SEE OFFER ebay

VICTRON ENERGY VE BS IP65 12/5 - Automatic charger for lead, lithium batteries, IP65, 12V/5A 104.05 EUR Battery charger with built-in Bluetooth. It is designed to charge 12 V batteries of various types and provided a maximum charging current of 5 A. Together with the free VictorConnect app, you can easily and smart evaluate the activity of your battery charger via your smartphone, tablet or computer and even configure it to a certain extent.

Technical Highlights:

Easy configuration and setup
Suitable for all 12 V battery types
Max. 5 a charging current
Automatic temperature adjustment at low or high temperatures
7-stage intelligent load algorithm
Can restore completely discharged batteries to ''dead batteries''
Has low-power mode for charging small batteries
Lithium-Ion Battery Mode

ultra-efficient ''green'' battery charger
With an efficiency of up to 95%, these chargers generate three to four times less heat than the industry standard. And, after the battery is fully charged, the power consumption is reduced to 0.5 watts, which is five to ten times better than the industry standard.

durable, safe and quiet

Low heat load on electronic components
Protected against the ingress of dust, water and chemicals.
Protection against overheating: The output current is reduced linearly when the temperature rises to 60 °C, so the charger does not fail even at extreme temperatures
The chargers are absolutely silent thanks to passive cooling: No fan or other moving parts

Reconditioning (Recovery)
A Lead-Acid Battery. If the charge was not sufficiently charged, or if the charge was left in the discharged state for days or weeks, its performance will deteriorate due to sulphation. If the process is stopped in time, it partially reverses the sulphation by charging the battery with low current until a higher voltage is reached.

Function for recovering completely discharged batteries
Most reverse polarity protected chargers do not recognize and therefore do not recharge a battery that has been discharged to zero volts or almost zero volts. However, the Blue Power charger will attempt to recharge a fully discharged low current battery and resume normal charging after sufficient voltage is established via the battery connector.

Includes:
1x Battery charger
1x operating instructions
1x terminals
1x M8 Cable lug connectors

SEE OFFER SEE OFFER ebay

VICTRON ENERGY VE BS IP65 24/5 - Automatic charger for lead-acid, lithium batteries, IP65, 24 V/5 115.06 EUR Victron Blue Smart IP65 battery charger 24 V 5 A with Bluetooth
The Victron Blue Power charger is a very efficient high frequency charger with a wide range of functions. The device measures the ambient temperature during the test phase and balances the temperature during charging. The temperature is measured again when the charger is in low current mode, in low voltage mode or in storage mode. Therefore, no special settings are required for a cold or hot environment. There is a low-energy mode for small batteries. It is also possible to charge lithium-ion batteries with this charger. After the battery is charged, the power consumption of the battery charger is reduced to 0.5 watts.

SEE OFFER SEE OFFER ebay

VICTRON ENERGY VE BS IP65 24/8 - Automatic charger for lead-acid, lithium batteries, IP65, 24 V/8 153.72 EUR Victron Blue Smart IP65 battery charger 24 V 8 A with Bluetooth
The Victron Blue Power charger is a very efficient high frequency charger with a wide range of functions. The device measures the ambient temperature during the test phase and balances the temperature during charging. The temperature is measured again when the charger is in low current mode, in low voltage mode or in storage mode. Therefore, no special settings are required for a cold or hot environment. There is a low-energy mode for small batteries. It is also possible to charge lithium-ion batteries with this charger. After the battery is charged, the power consumption of the battery charger is reduced to 0.5 watts.

SEE OFFER SEE OFFER ebay

VICTRON ENERGY VE BS IP65 12/10 - Automatic charger for lead-acid, lithium batteries, IP65 12 V/10 132.2 EUR Victron Blue Smart IP65 battery charger 12 V 10 A with Bluetooth
The Victron Blue Power charger is a very efficient high frequency charger with a wide range of functions. The device measures the ambient temperature during the test phase and balances the temperature during charging. The temperature is measured again when the charger is in low current mode, in low voltage mode or in storage mode. Therefore, no special settings are required for a cold or hot environment. There is a low-energy mode for small batteries. It is also possible to charge lithium-ion batteries with this charger. After the battery is charged, the power consumption of the battery charger is reduced to 0.5 watts.

SEE OFFER SEE OFFER ebay

ANSMANN ANS BC 6-12V-10A - Automatic charger for lead-acid and lithium batteries, IP65, 6 - 101.12 EUR 10-stage car charger for 6-V and 12-V lead-acid, lead-gel and AGM batteries, as well as 12-V LiFePO4 batteries

Intelligent and safe charging control even under frosty conditions with deep discharge protection.
Thanks to its wide range of features, ANSMANN's most powerful 10-stage charger BC 6 - 12 V/10 A ensures safe, battery-preserving charging of lead-acid batteries with a capacity of 7 - 200 Ah. It guarantees optimum performance and a long battery service life. The ''MODE'' button can be used to select 6 intelligent charging programs or a power supply mode that can be used to operate 12-V devices such as a cool box via the included car socket.

The charger is dustproof and protected against splash water (IP65) and has the following electrical safety features: reverse polarity protection, overcharge protection, deep discharge protection and short-circuit protection

In addition, the intelligent charger is suitable for standby/parallel operation and can remain connected to the battery at all times. It always keeps it fully charged, even if the battery is under load/discharging at the same time.

Fully automatic, intelligent ten-stage charging

SEE OFFER SEE OFFER ebay

H-TRONIC HTC 4000 - Automatic charger for lead-acid batteries, 12 V, 4 A, Li-ion 82.25 EUR The HTC 4000 is one of the most advanced and intelligent battery charging diagnostic and test devices. It works with state-of-the-art, characteristic curve-controlled charging technology and provides optimal battery charging and maintenance. Intelligent software constantly monitors the complete functions and controls the correct charging process depending on the condition of the battery.

I/U charging characteristic curve I-phase, U1 phase, U2 phase,
Protection against reverse polarity and short-circuit by means of an electronic protective circuit
Trickle charge
Battery test function, defect detection
For 12 V lead-acid batteries
For 12 V Li-ion starter batteries
Charging current max. 4 A (auto mode)
or max. 1 A (motorcycle mode)
15 LED indicators for the status

Technical data:
Operating voltage: 220 - 240 V/AC (50/60 Hz)
Final charge voltage: 14.3 V/14.7 V
Charging current (auto mode): max. 4 A
Charging current (motorcycle mode): max. 1 A
Protection class (housing): IP65
Operating conditions: -15°C to +45°C
Dimensions (L x W x H): 225 x 72 x 56 mm
Weight: Approx. 625 g
Length mains cable: approx. 1.50 m
Length charging cable (incl. accessories): approx. 1.90 m
Fuse (charging cable): 10 A
For 12 V lead-acid batteries and 12 V Li-ion starter batteries
Battery voltage: 12 V (6 cells for lead-acid batteries)
Battery capacity (recommended): 1.2 Ah to 120 Ah

Optional accessories for connection:
Vehicle connection: HTC vehicle
Eyelet connection: HTC FIX

SEE OFFER SEE OFFER ebay

ANSMANN ANS BC 6-12V-6A - Automatic charger for lead-acid and lithium batteries, IP65, 6 - 88.3 EUR 10-stage car charger for 6-V and 12-V lead-acid, lead-gel and AGM batteries, as well as 12-V LiFePO4 batteries

Intelligent and safe charging control even under frosty conditions with deep discharge protection.
Thanks to its wide range of features, the 10-stage charger BC 6 - 12 V/6 A ensures safe, battery-preserving charging of lead-acid batteries with a capacity of 4 - 150 Ah. It guarantees optimum performance and a long battery service life. The ''MODE'' button can be used to select 6 intelligent charging programs or a power supply mode that can be used to operate 12-V devices such as a cool box.

The charger is dustproof and protected against splash water (IP65) and has the following electrical safety features: reverse polarity protection, overcharge protection, deep discharge protection and short-circuit protection

In addition, the intelligent charger is suitable for standby/parallel operation and can remain connected to the battery at all times. It always keeps it fully charged, even if the battery is under load/discharging at the same time.

Fully automatic, intelligent ten-stage charging

SEE OFFER SEE OFFER ebay

ANSMANN ANS BC 6-12V-2A - Automatic charger for lead-acid and lithium batteries, IP65, 6 - 58.94 EUR 8-stage car charger for 6-V and 12-V lead-acid, lead-gel and AGM batteries, as well as 12-V LiFePO4 batteries

Intelligent and safe charging control
Thanks to its wide range of features, the 8-stage charger BC 6 - 12 V/2 A ensures safe, battery-preserving charging of lead-acid batteries with a capacity of 4 - 60 Ah. It guarantees optimum performance and a long battery service life. The ''MODE'' button can be used to select three intelligent charging programs, each with two charging currents.

The charger is dustproof and protected against splash water (IP65) and has the following electrical safety features: reverse polarity protection, overcharge protection, deep discharge protection and short-circuit protection

In addition, the intelligent charger is suitable for standby/parallel operation and can remain connected to the battery at all times. It always keeps it fully charged, even if the battery is under load/discharging at the same time.

Selectable charging programs:

6-V STD or 12-V STD: for lead-acid and lead-gel batteries
12-V LFP: for lithium-iron phosphate batteries (LiFePO4, LFP)

Charging currents of 1 A or 2 A can be selected for each charging program.

Fully automatic, intelligent eight-stage charging

SEE OFFER SEE OFFER ebay

VICTRON ENERGY VE BS IP65 12/7 - Automatic charger for lead-acid, lithium batteries, IP65 12 V/7 119.75 EUR Victron Blue Smart IP65 battery charger 12 V 7 A with Bluetooth
The Victron Blue Power charger is a very efficient high frequency charger with a wide range of functions. It is suitable for batteries with a capacity of 20 to 70 Ah. The device measures the ambient temperature during the test phase and balances the temperature during charging. The temperature is measured again when the charger is in low current mode, in low voltage mode or in storage mode. Therefore, no special settings are required for a cold or hot environment. There is a low-energy mode for small batteries. It is also possible to charge lithium-ion batteries with this charger. After the battery is charged, the power consumption of the battery charger is reduced to 0.5 watts.

SEE OFFER SEE OFFER ebay

VICTRON ENERGY VE BS IP22 12/30 - Automatic charger for lead, lithium batteries, IP22, 12V/30A 228.82 EUR The Blue Smart IP22 charger from Victron Energy, is a professional, compact 12 V 30 a battery charger of the latest generation with 3 charging outputs and built-in Bluetooth! The charger can be used with equipment in your workshop or with motor vehicles such as (classic) cars, motorcycles, boats and mobile homes and charges both classic 12 V lead-acid batteries and modern lithium batteries.

Technical Highlights:

Charges 12 V lead-acid, gel, AGM and lithium batteries
30 a maximum charging current
3 Battery Charging Outputs
State-of-the-art, seven-stage charging algorithm
With integrated Bluetooth for use with the free VictorConnect app

Intelligent charging, up to the perfect battery condition
The seven-stage charging algorithm gets the most out of your battery. The charger provides the battery with the energy it needs, keeps it in a healthy state, ensures better performance... and a longer life.

Recovery of deep-discharged ''dead'' batteries
Unlike most other brands and product lines, the Blue Smart IP22 charger will try to recharge a low-discharge battery by forcing it to have a low-charge current. Normal charging will then resume as soon as there is sufficient voltage between the battery terminals.

Remotely check battery status using the VictorConnect app
The Blue Smart charger has built-in Bluetooth. This allows you to check the status of the charger and battery on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictorConnect app.

Trend-setting efficiency
With an efficiency of up to 94%, these chargers generate up to four times less heat compared to the industry standard. After the battery has also been fully charged, the power consumption drops to less than 0.5 watts, which is about five to ten times better than the industry standard.

Storage mode: Less maintenance and aging when the battery is at rest
Storage mode is activated whenever no discharge has occurred within 24 hours. The charge maintenance voltage is then reduced to 2.2 V/cell (13.2 V for a 12 V battery) to minimize the gas development and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gas voltage. This provides a kind of equalizing charge that prevents electrolyte stratification and sulphation, the two main causes of premature battery failure.

SEE OFFER SEE OFFER ebay

IVT GMBH IVT SH-3.170 - Automatic charger for lead-acid and lithium batteries, IP20, 6/1 52.95 EUR Maintenance, winter hibernation, charge retention - compact chargers for lead and LiFePO4 batteries

With the handy SH-3.170, 2 A battery charger, you can reliably and safely charge your 6 V and 12 V lead-acid batteries as well as 12 V lithium batteries (LiFePO4) with a battery management system. It has also been optimised for the maintenance of car and motorcycle batteries.
The fully automatic, multi-stage charging procedure and the integrated trickle charging function constantly monitor the battery voltage and recharge the battery optimally as required. This ensures that the battery is always well maintained and ready to use at all times. Batteries in seasonal vehicles that are only used sporadically should therefore generally remain connected to the charger.

Features:

Suitable for 2 V, 6 V and 12 V lead-acid batteries (acid, gel, AGM)
Suitable for 12 V lithium batteries with BMS
Multi-stage, microprocessor-controlled charging process
Trickle charging function for immediate operational readiness
Regeneration mode for reactivating deeply discharged batteries
Equipped with auto-memory function
Protection against short circuit, reverse polarity and overcharging
Clear operating and display panel
Easy to operate using a button
Supplied with 2-piece charging adapter set

SEE OFFER SEE OFFER ebay

VICTRON ENERGY VE BS-IP22-12/20 - Automatic charger for lead, lithium batteries, IP22, 12V/20A 171.18 EUR The Blue Smart IP22 charger from Victron Energy, is a professional, compact 12 V 20 a battery charger of the latest generation with 3 charging outputs and built-in Bluetooth! The charger can be used with equipment in your workshop or with motor vehicles such as (classic) cars, motorcycles, boats and mobile homes and charges both classic 12 V lead-acid batteries and modern lithium batteries.

Technical Highlights:

Charges 12 V lead-acid, gel, AGM and lithium batteries
20 a maximum charging current
3 Battery Charging Outputs
State-of-the-art, seven-stage charging algorithm
With integrated Bluetooth for use with the free VictorConnect app

Intelligent charging, up to the perfect battery condition
The seven-stage charging algorithm gets the most out of your battery. The charger provides the battery with the energy it needs, keeps it in a healthy state, ensures better performance... and a longer life.

Recovery of deep-discharged ''dead'' batteries
Unlike most other brands and product lines, the Blue Smart IP22 charger will try to recharge a low-discharge battery by forcing it to have a low-charge current. Normal charging will then resume as soon as there is sufficient voltage between the battery terminals.

Remotely check battery status using the VictorConnect app
The Blue Smart charger has built-in Bluetooth. This allows you to check the status of the charger and battery on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictorConnect app.

Trend-setting efficiency
With an efficiency of up to 94%, these chargers generate up to four times less heat compared to the industry standard. After the battery has also been fully charged, the power consumption drops to less than 0.5 watts, which is about five to ten times better than the industry standard.

Storage mode: Less maintenance and aging when the battery is at rest
Storage mode is activated whenever no discharge has occurred within 24 hours. The charge maintenance voltage is then reduced to 2.2 V/cell (13.2 V for a 12 V battery) to minimize the gas development and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gas voltage. This provides a kind of equalizing charge that prevents electrolyte stratification and sulphation, the two main causes of premature battery failure.

SEE OFFER SEE OFFER ebay

VICTRON ENERGY VE BS IP65 12/25 - Automatic charger for lead-acid, lithium batteries, IP65, 12V/25 227 EUR The Blue Smart IP65 12/25(1) 12V 230V Battery Charger (BPC122531064) is Victron Energy's latest professional, charger with integrated Bluetooth® module. It charges 12V batteries of various types and delivered a maximum charging current of 25A. Together with the free VictronConnect app, you can thus easily and smartly evaluate the activity of your battery charger via your smartphone, tablet or computer and even configure it to a certain extent.

Technical highlights of the Blue Smart IP65 12/25(1)battery charger:

easy configuration and setup of the Blue Smart IP65 12/25(1) via Bluetooth® interface
max. 25A charging current, suitable for all 12V battery types
solid protection against splash water. dust and chemicals thanks to IP65 protection
has several functions to extend battery life
automatic temperature adjustment at low, respectively high temperatures
automatic power supply function
7-step intelligent charging algorithm
can recover completely discharged batteries ''dead batteries
has low energy mode for charging small batteries
lithium-ion battery mode

With up to 95% efficiency, these chargers generate three to four times less heat than the industry standard. And, after the battery is fully charged, power consumption is reduced to 0.5 watts, five to ten times better than the industry standard.
Durable, safe and quiet

low heat load on electronic components
protected against ingress of dust, water and chemicals.
protection against overheating: the output current is linearly reduced when the temperature rises up to 60°C, so the charger will not fail even in extreme temperatures
the chargers are absolutely silent thanks to passive cooling: no fan or other moving parts

Reconditioning (recovery)

A lead-acid battery that has not been sufficiently charged or has been left in a discharged state for days or weeks will deteriorate in performance due to sulfation. Provided the process is stopped in time, it allows the sulfation to be partially reversed by charging the battery at low current until a higher voltage is reached.

Restoring fully discharged batteries

Most chargers with reverse battery protection will not recognize a battery that has been discharged to zero volts or near zero volts, and therefore will not recharge it. However, the Blue Power charger will attempt to recharge a fully discharged battery with low current and will resume normal charging after sufficient voltage has been established across the battery terminals.

Scope of delivery:

1x Victron BPC122531064 Blue Smart IP65 12/25(1)230V battery charger for 12V batteries
1x user manual
1x connection terminals
1x M8 cable lug connector

SEE OFFER SEE OFFER ebay

ANSMANN ALCT 6-24 10 - Lead-acid battery charger - ALCT 6-24/10 94.66 EUR • Charger for 6 V, 12 V and 24 V lead-acid batteries (lead-gel, lead-fleece, lead-acid)
• A fast and reliable lead-acid battery contact is possible with the high-quality terminal posts.
• Automatic voltage detection
• Clear LED display — easy to use
• Adjustable charging current
• Auto-REFRESH mode when the battery has been deeply discharged
• Selectable COLD TEMPERATURE mode for cold temperatures
• Faulty battery detection
• 3-stage battery status display (35% - 70% - 100%)
• Electronic protection against short circuit, reverse polarity and overcharging
• Automatic recharge if the battery is left connected to the charger
• Ideal for hibernation of lead-acid batteries — deep discharge excluded
• Automatic start-up support (6 V - 1 A 12 V - 10 A 24 V - 5 A)
• Power cable and charging cable 180 cm
• Practical integrated cable storage compartment ensures all cables are always safely stowed away

Technical data:
Battery capacity 4.5 Ah - 240 Ah
Weight: only 1300 g due to state-of-the-art switching power supply technology
Operating voltage: 230 V/50 Hz
Dimensions (W x H x D): 272 x 194 x 142 mm

• Different charging modes selectable:
1 A at 6 V, 12 V, 24 V
5 A at 12 V, 24 V
10 A at 12 V

COLD TEMP mode: Recommended for temperatures below 5°C, ensuring that the battery is fully charged even in cold temperatures.

REFRESH mode: The charger automatically detects when the battery has been deeply discharged and gently charges it by means of pulsating charging currents for 20 minutes until a base voltage is reached. A normal charging process can then be performed.

SEE OFFER SEE OFFER ebay

VELLEMAN AC30 - Automatic charger, 12/24 V, 20 A 129.47 EUR Charger for 12-/24-V lead-acid batteries with 20-A boost function

Portable single-phase charger for 12-/24-V lead-acid batteries.

Overload protection (charger)
Built-in ammeter
For cars and vans

Technical features:
Input voltage: 230 VAC
Frequency: 50 Hz
Output current: 16 A
Boost current: 20 A
Replaceable fuse: 30 A
Reference battery capacity: min. 92 Ah - max. 250 Ah

SEE OFFER SEE OFFER ebay

ALCS 2-12 - ANSMANN ALCS 2-12/0.4, charger for lead-acid batteries 29.28 EUR Charger for 2 V, 6 V and 12 V lead-acid batteries (lead-gel, lead-fleece, lead-acid) with 3.5 m charging cable. Also ideal for winter hibernation of lead-acid batteries.

• Suitable for standby mode and parallel operation
• Charging according to IU characteristic curve
• Automatic recharge for continuous connection

Technical data:
Battery voltage: 2 V, 6 V, 12 V
Operating voltage: 100 - 240 V
Recommended battery capacity at 12 V: max. 40 Ah
Recommended battery capacity at 2 V: min. 1.2 Ah
Suitable for (car batteries): Lead-fleece, lead-acid, lead-gel

SEE OFFER SEE OFFER ebay

NEDIS N BACCH02 - Battery charger for lead acid batteries, 2 /6 / 12 V 30.61 EUR Compact automatic lead-acid battery charger for batteries with capacities between 2.2 and 10 Ah.

• charges 2 V, 6 V and 12 V batteries
• fully automatic charger
• ends charging with the battery fully charged
• Voltage selector switch
• Short circuit protection, reverse polarity protection

Product details
Input voltage of 230 VAC
Full protection of the battery from overcharging
Short circuit and overcurrent protection
Reverse polarity protection

SEE OFFER SEE OFFER ebay

H-TRONIC AL 1600 - AL 1600 automatic charger for 6 - 8 - 12 V 38.84 EUR With this automatic plug-in charger in state-of-the-art switching power supply technology, 6 V, 8 V and 12 V lead-acid batteries are automatically loaded. Compared to conventional chargers, this charger is characterised by a higher degree of efficiency (up to 85%) and a significantly low weight and smaller dimensions with the same power. The integrated electronic charge controller automatically reduces the charging current when the respective final charge voltage is reached. Ideally suited to vehicle, caravan, motorcycle and boat or tractor batteries. The charger can remain connected to the battery with no time limit and is, therefore, also ideal for the winter hibernation of batteries. Delivery includes battery terminals and instructions.

Features:
• State-of-the-art switching power supply technology
• Protection against short circuit and reverse polarity
• Constant final charge voltage
• Automatic charging current adjustment
• No charging when the battery is connected with reversed polarity
• The battery is only charged when properly connected
• Visual display for network, charging and reverse polarity
• Electronic protection against short-circuit, reverse polarity and overcharging

Technical data:
Operating voltage: 220-240 V/50-60 Hz
Final charge voltage: Adjustable to 6.9/9.2/13.8 V using slide switch
Max. charging current: 1.6 A constant final charge voltage
Dimensions: 93 x 65 x 59 mm (L x W x H)
Weight: approx. 255 g

SEE OFFER SEE OFFER ebay

KS TOOLS GMBH KS 550.1645 - 12-V digital battery tester 200.12 EUR 12-V digital battery tester

Description

Suitable for 12-V batteries (lead acid, gel, wet cell, MF, VRLA, calcium, AGM and low cycle batteries)
Automatic control of the complete test process by menu navigation
For quick and easy determination of the battery performance, taking into account the temperature compensation
Checks battery status, charge status, internal resistance, cold start current value
With check function for starter battery, starter and charging circuit measurement
The measurement results are displayed by a precise five-digit LCD display
In addition, the measurement results are displayed by colour symbols: OK, Charging and Bad
Connection to the battery is via two plastic-sheathed crocodile clips
Avoid overloading the battery through an excessively long measurement time
Illuminated and very easy-to-read LCD display
0.45-m long cable allows flexible working
Durable rubber sleeve coating

Features

Display: LCD
Voltage range: 7.6 - 17 V
Packaging length: 283 mm
Frequency: 100
Packaging height: 65 mm
Accuracy 1: +/- 0.5 megaohm
Weight [g]: 1000
Package content: 1
Measuring range: 7.6 - 17 V
Packaging: card
Operating temperature: -18°C to 55°C
SAE work area: 100 - 1.400 CCA
IEC work area: 100 - 800 CCA
EN work area: 100 - 1.400 CCA
DIN work area: 100 - 800 CCA
CCA work area: 100 - 1.400 CCA
General application: for 12-V starter batteries
Packaging width: 167 mm

SEE OFFER SEE OFFER ebay

EINHELL 1002265 - Automatic charger for lead-acid batteries, 12 V. 144.73 EUR The Einbright Battery Charger CE-BC 15 M is an intelligent battery charger adapted to the technically advanced and low-noise batteries of modern vehicles. The intelligent battery charger with microprocessor control is suitable for a wide range of battery types in vehicles and has a range of technical protection and care mechanisms. The main focus of the development was on a fast, gentle charging of the batteries, so that the longest possible service life at full power is achieved. The operation of the charger is easier than with conventional devices thanks to a detailed charging display. The single-light all-rounder is suitable for gel batteries, AGM, as well as maintenance-free and low-maintenance lead acid batteries. The CE-BC 15 M automatically adjusts to the battery voltage of 12 V vehicles. The multi-stage charging cycle of the Einbright battery charger is automatically monitored and adjusted by the microprocessor control. The smart control electronics analyze the type and condition of the connected battery and initiate the optimal mode on demand. The maintenance charging function protects and protects the battery for a permanently ideal charge state. The Einbright battery charger can support the battery with 100 a starting current (max. 5 seconds) by means of an external start function.

Intelligent battery charger with microprocessor control
Multi-stage charging cycle, microprocessor controlled and monitored
2 in 1: Charge and power off with one device
Maintenance charging function for a permanent, ideal charge state
All-round battery charger for a wide range of battery types
For gel, AGM, maintenance-free and low-maintenance lead-acid batteries
Use extends battery life
LED battery voltage and charge progress indicator
Electronic overload, short circuit and reverse polarity protection
Fully insulated battery terminals
Ergonomic handle for optimal transport

Technical Data:
Power supply: 230 V/ 50 Hz
Charging voltage: 12 V.
Starting aid: 100 a - 5 sec.
Charging current min./ max.:2.7/ 15 A.

SEE OFFER SEE OFFER ebay

IWH VERTRIEBS GMBH IWH 075900 - Automatic charger for lead batteries, LiFePO4, 6/12 V, 4 A

Comparison of Similar Products