EXSYS EX-46014 - PCI Express card for 4x RS-232
49.18 EUR
Access the complete sheet with information, compare prices and discover the features of PRODUCTNAME, available at the price of PRICE CURRENCY; it falls into the CATEGORY NAME; the sale is managed by SELLER NAME and the production is done by MANUFACTURER NAME.
The EX-46014 PCIe I/O card provides four serial RS-232 high-performance UART 16C550 outputs. It was developed to add four additional serial ports for a PC, small workstation or server via the PCIe bus. The four 9-pin connectors are mounted on two slot plates. Four low profile plates are supplied for narrow calculators.
EAN: 4718359460142
Delivery Cost: 9.95 EUR
Availability: in stock
Delivery Time: 4-5 business days
Condition: new
- RS-232 V.24 interface
- FIFO buffer: 16C550 with 256 bytes
- I/O addresses and interrupt are assigned by the operating system
- PCIe interface compatible with 2.0 Gen 1 specifications
- Data bits: 5, 6, 7 and 8
- Stop bits: 1, 1.5 and 2
- Parity: none, even, odd, space and mark
- RS-232 signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- Chip set: ASIX AX99100
- Includes: EX-46014, 4x low profile brackets, manual
The EX-46014 PCIe I/O card provides four serial RS-232 high-performance UART 16C550 outputs. It was developed to add four additional serial ports for a PC, small workstation or server via the PCIe bus. The four 9-pin connectors are mounted on two slot plates. Four low profile plates are supplied for narrow calculators.
- Category: serial cards
- Interface: RS-232
- Ports: 9-pin connector
- Number of ports: 4
- Bus system: PCIe
- Design: standard + low profile
EAN: 4718359460142
Delivery Cost: 9.95 EUR
Availability: in stock
Delivery Time: 4-5 business days
Condition: new
Comparison of Similar Products
EXSYS EX-45364 - PCI Express card for 4x RS-232/422/485
205.3 EUR
- Interface: 4x RS-232 V.24, RS-422/485 - independent mode selection
- FIFO buffer: 16C1050 with 256 bytes
- I/O addresses and interrupt: assigned by the system BIOS, IRQ sharing
- Data bits: 5, 6, 7, 8/stop bits: 1, 1.5, 2
- Parity: none, even, odd, space, mark
- Signals RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- RS-422/485 signals
- - RS-422 - 4 wire (TXD+/-, RXD+/-) (full duplex)
- - RS-485 - 4 wire (TXD+/-, RXD+/-) (full duplex)
- - RS-485 - 2 wire (Data+/-, Data+/-) half duplex)
- Supports ATTATM Auto Transmitter
- RS-422/485 termination - 120 ohms can be switched on or off
- Chip set: SystemBase SB16C1054PCI
The EX-45364 PCI I/O card provides 4 serial RS-232, 422 and 485 high-performance UART 16C1050 outputs. Each port can be set independently of the interface type. It was developed to add four additional serial combo ports for PCs, small workstations or servers via the PCIe bus.
The card is fully PCIe plug and play compatible and has no problems with IRQ and I/O address conflicts. It supports the ATATM Auto RS-485 Transmitter features.
EXSYS EX-44044-2 - PCI Express card to 4x RS-232
101.89 EUR
- Interface: RS-232 V.24
- FIFO buffer: 16C550 with 16 bytes
- ±15kV IEC1000-4-2 ESD protection for RS232 I/O.
- I/O addresses and interrupt is assigned by the operating system, IRQ sharing
- Data bits: 5, 6, 7, 8/stop bits: 1, 1.5, 2/parity: none, even, odd, space, mark
- Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- PCI Express interface compatible with 1.0a specification
- Chip set: Asmedia MCS9904CV
The EX-44044-2 PCI Express I/O card provides four serial RS-232 high-performance UART 16C550 outputs. It was developed to add four additional serial outputs for a PC, small workstation or server via the PCI Express bus.
The card is fully PCI-Express Plug-and-Play compatible and has no problems with IRQ and I/O address conflicts. In addition, +5 V or +12 V can be configured on pin 9 of the serial connector for a POS system (power over system). With the EX-44044-2 a low profile bracket is supplied, for narrow computer housings up to 8 cm height.
EXSYS EX-46024 - PCI Express card for 4x RS-232, cable
68.81 EUR
- RS-232 V.24 interface
- FIFO buffer: 16C550 with 256 bytes
- I/O addresses and interrupt are assigned by the operating system
- PCIe interface compatible with 2.0 Gen 1 specifications
- Data bits: 5, 6, 7 and 8
- Stop bits: 1, 1.5 and 2
- Parity: none, even, odd, space and mark
- RS-232 signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- Chip set: ASIX AX99100
- Includes: EX-46024, octopus cable, low profile bracket, manual
The EX-46024 PCIe I/O card provides four serial RS-232 high-performance UART 16C550 outputs. It was developed to add four additional serial ports for a PC, small workstation or server via the PCIe bus. The four 9-pin connectors are connected via an octopus cable. This requires only the space of a slot plate. The EX-46024 comes with a low profile bracket for slim computer enclosures up to 8 cm in height.
- Category: serial cards
- Interface: RS-232
- Ports: 9-pin connector
- Number of ports: 4
- Bus system: PCIe
- Design: standard + low profile
EXSYS EX-45034 - PCI Express card to 4x serial RS-232/422/485
150.47 EUR
- Interface: RS-232 V.24/RS-422/RS-485
- ±15-kV IEC1000-4-2 ESD protection for RS232 I/Os
- FIFO buffer 16C550 with 16 bytes
- I/O addresses and interrupt are assigned by the operating system
- Data bits: 7 and 8/stop bits: 1, 1.5, 2
- Parity: none, even, odd, space and mark
- Supports ATTATM Auto Transmitter
- RS-422/485 termination - 120 ohms can be switched on or off
- Chip set: FTDI
Signals:
- RS-232 - TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- RS-422 - 4 wire (TxD+/-, RxD+/-) full duplex
- RS-485 - 4 wire (TxD+/-, RxD+/-) full duplex
- RS-485 - 2 wire (Data+/-, Data+/-) half duplex
The EX-45034 PCI I/O card provides 4 serial RS-232, 422 and 485 high-performance UART 16C550 outputs. It was developed to add four additional serial ports for a PCs, small workstations or servers via the PCI or PCI-X bus. +5 V and +12 V can be configured on pin 9 of the serial connector for a POS system.
The card is fully plug-and-play compatible. It supports the ATTATM Auto RS-485 Transmitter features. The RS-232, 422 or 485 transmission type can be set individually for each port.
EXSYS EX-44083 - PCI Express card for 1x 9-pin, 1x 25-pin RS-232
64.68 EUR
- RS-232, V.24 interface
- ±15kV IEC1000-4-2 ESD protection for RS232 I/O.
- FIFO buffer: 16C550 with 16 bytes
- I/O addresses and interrupt are assigned by the operating system
- PCIe interface compatible with 1.0a to 3.0 specifications
- 5, 6, 7, and 8 data bits
- 1, 1.5, and 2 stop bits
- Parity: none, even, odd, space and mark
- Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- Supports RTS/CTS and XON/XOFF Flow Control
- Supports +5V or +12V on pin 9 of all serial plugs
- Chip set: ASIX AZ99100
The EX-44083 PCI Express I/O card provides two serial RS-232 high-performance UART 16C550 outputs. It was developed to add four additional serial outputs for a PC, small workstation or server via the PCI Express bus.
The card is fully plug-and-play compatible. In addition, +5 V or +12 V can be configured on pin 9 of the serial connector for a POS system (power over system). With the EX-44082, two low profile brackets are supplied for installation in narrow computer housings up to 8 cm height.
EXSYS EX-44062 - PCI Express card for 2x RS-232
69.85 EUR
- Interface: RS-232 V.24 with FIFO buffer 16C1050 with 256 bytes
- ±15kV IEC1000-4-2 ESD protection for RS232 I/O.
- I/O addresses and interrupt is assigned by the operating system, IRQ sharing
- PCIe interface compatible with 1.0a to 3.0 specifications
- Data bits: 5, 6, 7, 8
- Stop bits: 1, 1.5, 2
- Parity: none, even, odd, space, mark
- Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- Supports RTS/CTS and XON/XOFF Flow Control
- Supports +5V or +12V on pin 9 of the serial connector
- Chip set: Asmedia SB16C1053APCI
The EX-44062 PCI Express I/O card provides two serial RS-232 high-performance UART 16C1050 outputs. It was developed to add two additional serial outputs for a PC, small workstation or server via the PCI Express bus.
The card is fully PCI-Express Plug-and-Play compatible and has no problems with IRQ and I/O address conflicts. In addition, +5 V or +12 V can be configured on pin 9 of the serial connector for a POS system (power over system). With the EX-44062, two low profile brackets are supplied.
EXSYS EX-44081 - PCI Express card for 1x RS-232
58.48 EUR
- RS-232, V.24 interface
- ±15kV IEC1000-4-2 ESD protection for RS232 I/O.
- FIFO buffer: 16C550 with 16 bytes
- I/O addresses and interrupt are assigned by the operating system
- PCIe interface compatible with 1.0a to 3.0 specifications
- 5, 6, 7, and 8 data bits
- 1, 1.5, and 2 stop bits
- Parity: none, even, odd, space and mark
- Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- Supports RTS/CTS and XON/XOFF Flow Control
- Supports +5V or +12V on pin 9 of all serial plugs
- Chip set: ASIX AZ99100
The PCI I/O card provides a serial RS-232 high-performance UART 16C550 output. It was developed to add four additional serial outputs for a PC, small workstation or server via the PCI Express bus. The card is fully plug-and-play compatible. In addition, +5 V or +12 V can be configured on pin 9 of the serial connector for a POS system (power over system). With the EX-44081 a low profile bracket is supplied for installation in narrow computer housings up to 8 cm height.
EXSYS EX-45368 - PCI Express card for 8x RS-232/422/485
319.52 EUR
- Interface: 8x RS-232 V.24, RS-422/485 - independent mode selection
- FIFO buffer: 16C1050 with 256 bytes
- ±15-kV IEC1000-4-2 ESD protection for RS232 I/Os
- I/O addresses and interrupt: assigned by the system BIOS, IRQ sharing
- Data bits: 5, 6, 7, 8/stop bits: 1, 1.5, 2/parity: none, even, odd, space, mark
- Supports ATTA TM Auto Transmitter
- Supports PCIe slot versions 1.0 to 3.0
- RS-422/485 termination - 120 ohms can be switched on or off
- Signals RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- RS-422/485 signals:
- - RS-422 - 4 wire (TXD+/-, RXD+/-) (full duplex)
- - RS-485 - 4 wire (TXD+/-, RXD+/-) (full duplex)
- - RS-485 - 2 wire (Data+/-, Data+/-) half duplex)
- Chip set: SystemBase SB16C1058PCI
The EX-45368 PCI I/O card provides 8 serial RS-232, 422 and 485 high-performance UART 16C1050 outputs. Each port can be set independently of the interface type. It was developed to add eight additional serial combo ports for PCs, small workstations or servers via the PCIe bus.
EXSYS EX-45032IS - PCI Express card for 2x serial RS-232/422/485, opt. iso.
185.61 EUR
- Interface: RS-232 V.24/RS-422/RS-485
- 15-kV ESD over-voltage protection and 2.5-kV optical isolation
- ±15-kV IEC1000-4-2 ESD protection for RS232 I/Os
- FIFO buffer 16C550 with 16 bytes
- I/O addresses and interrupt are assigned by the operating system
- Data bits: 7 and 8/stop bits: 1, 1.5, 2
- Parity: none, even, odd, space and mark
- Supports ATTATM Auto Transmitter
- RS-422/485 termination - 120 ohms can be switched on or off
- Chip set: FTDI
Signals:
- RS-232 - TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- RS-422 - 4 wire (TxD+/-, RxD+/-) full duplex
- RS-485 - 4 wire (TxD+/-, RxD+/-) full duplex
- RS-485 - 2 wire (Data+/-, Data+/-) half duplex
The EX-45032IS PCIe I/O card provides 2 serial RS-232, 422 and 485 high-performance UART 16C550 outputs with 15-kV ESD overvoltage protection and 2.5-kV optical isolation. It was developed to add 2o additional serial ports for PCs, small workstations or servers via the PCIe bus.
It supports the ATTATM Auto RS-485 Transmitter features. The RS-232, 422 or 485 transmission type can be set individually for each port. POS is not adjustable.
EXSYS EX-44082 - PCI Express card for 2x RS-232
52.28 EUR
- RS-232, V.24 interface
- ±15kV IEC1000-4-2 ESD protection for RS232 I/O.
- FIFO buffer: 16C550 with 16 bytes
- I/O addresses and interrupt are assigned by the operating system
- PCIe interface compatible with 1.0a to 3.0 specifications
- 5, 6, 7, and 8 data bits
- 1, 1.5, and 2 stop bits
- Parity: none, even, odd, space and mark
- Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- Supports RTS/CTS and XON/XOFF Flow Control
- Supports +5V or +12V on pin 9 of all serial plugs
- Chip set: ASIX AZ99100
The EX-44082 PCI Express I/O card provides two serial RS-232 high-performance UART 16C550 outputs. It was developed to add four additional serial outputs for a PC, small workstation or server via the PCI Express bus. The card is fully plug-and-play compatible. In addition, +5 V or +12 V can be configured on pin 9 of the serial connector for a POS system (power over system). With the EX-44082, two low profile brackets are supplied for installation in narrow computer housings up to 8 cm height.
EXSYS EX-44316-2 - PCI Express card to 16x RS-232
402.67 EUR
- Interface: RS-232 V.24 with FIFO buffer 16C1050 with 256 bytes
- ±15kV IEC1000-4-2 ESD protection for RS232 I/O.
- PCIe interface compatible with 1.0a to 3.0 specifications
- I/O addresses and interrupt is assigned by the operating system, IRQ sharing
- Data bits: 5, 6, 7, 8/stop bits: 1, 1.5, 2
- Parity: none, even, odd, space, mark
- Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- Supports RTS/CTS and XON/XOFF Flow Control
- Supports +5V or +12V on pin 9 of the serial connector
- Chip set: 2 x Asmedia SB16C1054PCI
The EX-44316-2 PCI Express I/O card provides two serial RS-232 high-performance UART 16C1050 outputs. It was developed to add four additional serial outputs for a PC, small workstation or server via the PCI Express bus.
The card is fully PCI-Express Plug-and-Play compatible and has no problems with IRQ and I/O address conflicts. In addition, +5 V or +12 V can be configured on pin 9 of the serial connector for a POS system (power over system). An Octopus cable is supplied with the EX-44316-2. With the EX-44316-2 becomes a low profile.
EXSYS EX-46028 - PCI Express card for 8x RS-232, cable
144.27 EUR
- RS-232 V.24 interface
- FIFO buffer: 16C550 with 256 bytes
- I/O addresses and interrupt are assigned by the operating system
- PCIe interface compatible with 2.0 Gen 1 specifications
- Data bits: 5, 6, 7 and 8
- Stop bits: 1, 1.5 and 2
- Parity: none, even, odd, space and mark
- RS-232 signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- Supports RTS/CTS and XON/XOFF Flow Control
- Chip set: Exar/MaxLinear 17V358
- Includes: EX-46028, octopus cable, low profile bracket, manual
The EX-46028 PCIe I/O card provides eight serial RS-232 high-performance UART 16C550 outputs. It was developed to add eight additional serial ports for a PC, small workstation or server via the PCIe bus. The eight 9-pin connectors are connected via an octopus cable. This requires only the space of a slot plate. The EX-46028 comes with a low profile bracket for slim computer enclosures up to 8 cm in height.
- Category: serial cards
- Interface: RS-232
- Ports: 9-pin connector
- Number of ports: 8
- Bus system: PCIe
- Design: standard + low profile
EXSYS EX-46012 - PCI Express card for 2x RS-232
39.87 EUR
- RS-232 V.24 interface
- FIFO buffer: 16C550 with 256 bytes
- I/O addresses and interrupt are assigned by the operating system
- PCIe interface compatible with 1.1 specifications
- Data bits: 5, 6, 7 and 8
- Stop bits: 1, 1.5 and 2
- Parity: none, even, odd, space and mark
- RS-232 signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- Chip set: ASIX MCS9901CV-CC
- Includes: EX-46012, 2x low profile brackets, manual
The EX-46012 PCIe I/O card provides two serial RS-232 high-performance UART 16C550 outputs. It was developed to add two additional serial ports for a PC, small workstation or server via the PCIe bus. The EX-46012 comes with two low profile brackets for slim computer enclosures up to 8 cm in height.
- Category: serial cards
- Interface: RS-232
- Ports: 9-pin connector
- Number of ports: 2
- Bus system: PCIe
- Design: standard + low profile
EXSYS EX-45032 - PCI Express card > 2 x serial RS-422/485
108.09 EUR
- INTERFACE: RS-232 V.24 / RS-422 / RS-485
- ±15kV IEC1000-4-2 ESD protection for RS232 I/O.
- FIFO buffer: 16C550 with 16 bytes
- I/O addresses and interrupt are assigned by the operating system
- Data bits: 5, 7, 7, 8/stop bits: 1, 1.5, 2
- Parity: none, even, odd, space and mark
- Supports ATTATM Auto Transmitter
- Terminal: 120 ohms, can be switched on or off
Signals:
- Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- RS-422 - 4 wire (TxD+/-, RxD+/-) full duplex
- RS-485 - 4 wire (TxD+/-, RxD+/-) full duplex
- RS-485: two-wire - Data+, Data- and GND
The EX-45032 PCI Express I/O card provides two serial RS-232 high-performance UART 16C550 outputs. It was developed to add four additional serial outputs for a PC, small workstation or server via the PCI or PCI-X bus. Can be configured +5 V and +12 V on pin 9 of the serial connector for a POS system (power over system).
The card is fully plug-and-play compatible. It supports the ATTATM Auto RS-485 Transmitter features. The RS-232, 422 or 485 transmission type can be set individually for each port.
EXSYS EX-6072-4K - Network card, PCI Express, Gigabit Ethernet, 2x RJ45
97.76 EUR
The EX-6072-4K is a fast Dual Gigabit Ethernet card, designed for the PCIe bus, which offers faster data transfer compared to the PCI BUS. The EX-6072-4K supports a data transfer rate of up to 1000MBit per second per port.
The EX-6072-4K has an optical isolation of up to 4kV for each port. Larger amounts of data can thus be transmitted faster and more efficiently in the network.
The EX-6072-4K supports half and full duplex and NWay auto-negotiation to automatically adjust to network speed (10/100/1000 Mbps).
The card is also equipped with Auto-MDI/MDI-X. In addition, it offers a very wide-ranging support of various operating systems.
A low profile bracket is supplied with the card for installation in a narrow PC housing.
- Supports 10/100/1000Base-T Ethernet standard
- Supports 4kV optical isolation for each output
- Supports Auto-MDI/MDI-X Auto (for crossover cable)
- Supports Jumbo Frame up to 9KBytes, pair Swap/polarity/Skew Correction
- Wake-on-LAN and Remote Wake-up
- Supports Full Duplex Flow Control (IEEE 802.3x)
- Supports IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.1Q VLAN tagging, IEEE 802.1p Layer 2 priority encoding
- 48KB Buffer transmit/Receiver Chip
- LED display of data transmission
EXSYS EX-6074P-2 - Network card, PCI Express, Gigabit Ethernet, 4x RJ45
299.31 EUR
PCIe Quad network card with 4x 1Gigabit, PoE- Supports four PoE Gigabit Ethernet ports with 15.40W or 30.20 W
- Supplies network end devices with power via the data line
- Supports 10/100/1000 Base-T Ethernet standard
- Fully compatible with IEEE 802.3at PoE+ (PSE) Type 1 and 2 operation
- Maximum power output: Type 1 = 15.40 W / Type 2 = 30.20 W
- Supports Auto-MDI/MDI-X Auto (for crossover cable)
- Supports Pair Swap/Polarity/Skew Correction
- Wake-on-LAN and remote wake-up
- Supports Full Duplex Flow Control (IEEE 802.3x)
- Supports IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.1Q VLAN tagging, IEEE 802.1P Layer 2 Priority Encoding
- 48KB Buffer Transmit/Receiver Chip / LED indication of data transmission
- Chipset: 4x Realtek RTL8111G
The EX-6074PoE-2 is a fast Quad Gigabit Ethernet PCIe card.
It can supply end devices such as IP telephones, IP cameras or WLAN access points with a voltage of 48VDC via the network cable.
This means that the end devices do not require additional sockets or expensive switches that support PoE.
The EX-6074PoE-2 provides you with a cost-effective solution with a maximum output of 34.20 W and a maximum data transfer rate of 1000 Mbps.
The various end devices can be supplied with power directly via the data lines.
This saves costs and increases flexibility as to where the end devices are installed.
The EX-6074PoE-2 supports half and full duplex as well as Nway auto-negotiation to automatically adapt to the network speed (10/100/1000 Mbit/sec.).
The card is also equipped with Auto-MDI/MDI-X.
Scope of delivery:
- EX-6074PoE-2
- Driver CD
- User manual
EXSYS EX-60115 - Network card, PCI Express, 2.5 Gigabit Ethernet, 4x RJ45
216.62 EUR
4 port 2.5 Gigabit PCIe network card (4x Intel I225-V chipset)- Supports 10/100/1000/2500 Base-T Ethernet standard
- Supports 4-lane 2.5/5Gbps PCI Express bus
- Fully compatible with PCI Express 3.1
- Supports Jumbo Frame up to 9KBytes
- Automatic cross-over detection (MDI/ MDI-X)
- Supports Preboot eXecution Environment (PXE)
- Supports Legacy and Message Signal Interrupt (MSI/MSI-X)
- IEEE 802.3 auto-negotiator - automatic connection configuration for speed, duplex and flow control
- Time stamping and synchronization of time-critical applications.
- Scalable I/O for Linux environments (IPv4, IPv6, TCP/UDP)
- IEEE 802.3az - Energy Efficient Ethernet (EEE)
- Active State Power Management (ASPM)
- MAC Power Management Control
- Full wake-up support (APM/ACPI)
- Latency Tolerance Reporting (LTR)
- LED indicator for activity and data transfer mode
- Chipset: 4x Intel I225-V
The EX-60115 is a 2.5 Gigabit Ethernet card with four RJ45 ports for the PCIe bus.
It supports half and full duplex as well as auto-negotiation for automatic adaptation to the network speed (10/100/1000/2500 Mbit/s).
Thanks to PCI Express x4 with four lanes, sufficient bandwidth is available to provide the full performance of 2.5 Gbit/s on all four Ethernet ports simultaneously.
Scope of delivery:
- EX-60115
- Low profile bracket
- Instruction manual
DELOCK 89335 - PCI Express card > 4 x serial RS-232 HS/SPV
110.16 EUR
The Delock PCI Express card expands your system by four external high-speed RS-232 ports. Use this card for applications such as recording measured values, machine control, automation, development or communication. The comprehensive surge protection and extended temperature range also make this card suitable for use in the industrial sector. Connected devices can be supplied with a voltage of 5 V or 12 V.Technical data
• Chipset: Exar 17V354
• Connections:
External:
1 x Sub-D 44-pin socket
Connection cable: D-sub 44-pin plug > 4 x serial RS-232
Sub-D 9-pin plug
Internal:
1 x PCI Express x1, V2.0
1 x 4-pin Molex power connector
• Baud rate: up to 921.6 Mb/s
• Compatible with 16C550 UART
• 256 Byte FIFO
• Data bits: 5, 6, 7, 8
• Stop bits: 1, 1.5, 2
• Parity: none, even, odd, space, mark
• Flow control: RTS/CTS, XON/XOFF
• Adjustable power supply 5 V/12 V or RI on pin 9
• Operating temperature: -30°C - +75°C
• Storage temperature: -40°C - +85°C
• Relative humidity up to 95% (non-condensing)
• 15-kV ESD protection for all signals
• I/O addresses and IRQ are assigned by the system
System requirements
• Windows XP/XP-64/Vista/Vista-64/7/7-64, Linux from Kernel 2.6
• PC with one free PCI Express slot
• Power supply unit with one free Molex power connector
Package contents
• PCI Express card
• Low profile trim
• 1 serial connection cable (approx. 30 cm)
• CD driver
• User manual
Packaging
• Box
DELOCK 89557 - PCI Express Card > 4 x Serial RS-232
45.04 EUR
The PCI Express card by Delock expands a PC by four external serial ports. Different devices such as scanner, printer, mouse etc. can be connected to this card. By using the included low profile brackets, the PCI Express card can be also installed into a Mini-PC.Specification
• Connector:
external:
2 x serial RS-232 DB9 male
2 x serial RS-232 DB9 male (separate rear bracket)
internal:
1 x PCI Express x1, V2.0
• Chipset: ASIX AX99100
• Data transfer rate up to 230.4 Kb/s
• FIFO: 256 byte
• Compatible with 16C950 UART
System requirements
• Windows 7/7-64/8.1/8.1-64/10/10-64
• PC with one free PCI Express slot
Package content
• PCI Express card
• Slot bracket
• 4 x low profile bracket
• Driver CD
• User manual
Package
• Retail Box
EXSYS EX6072POE2 - Network card, PCI Express, Gigabit Ethernet, 2x RJ45
144.22 EUR
The EX-6072PoE-2 is a fast Dual Gigabit Ethernet card designed for the PCIe bus. - Supports 10/100/1000 Base-T Ethernet standard
- Fully compatible with IEEE 802.3af PoE (PSE) Type 1 = 15.40W and IEEE802.3af PoE+ (PSE) Type 2 = 34.20W
- Maximum power delivered (PD): Type 1 = 12.95W / Type 2 = 25.50W
- Supports Auto-MDI/MDI-X Auto (for crossover cable)
- Supports Pair Swap/Polarity/Skew Correction
- Wake-on-LAN and Remote Wake-up
- Supports Full Duplex Flow Control (IEEE 802.3x)
- Supports IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.1Q VLAN tagging, IEEE 802.1P Layer 2 Priority Encoding
- Microsoft NDIS 5 checksum offload (IP, TCP, UDP), Supports PCI Message Signaled Interrupt (MSI)
- 48KB Buffer Transmit/Receiver Chip
- LED indication of data transmission
- Chipset: Realtek RTL8111G
Gigabit PoE
The EX-6072PoE-2 supports ''Power over Ethernet'' and has a data transfer rate of up to 1000 MBit/s and thus offers a high speed increase compared to standard PCI network cards.
Larger amounts of data can thus be transferred faster and more efficiently in the network.
Any end devices that support Power over Ethernet can be connected to the EX-6072PoE-2 without additional PoE switches.
Network Features
The EX-6072PoE-2 supports half and full duplex as well as NWay auto-negotiation to automatically adapt to the network speed (10/100/1000 Mbps).
Furthermore the card is equipped with Auto-MDI/MDI-X.
Compatibility
It also offers a very wide support of various operating systems.
Included Low Profile bracket
A low profile bracket is supplied with the card for installation in a narrow PC case.
Scope of delivery:
- EX-6072PoE-2
- Low Profile bracket
- Driver CD
- Manual
EXSYS EX-6071C - Network card, PCI Express, Gigabit Ethernet, 1x RJ45
66.75 EUR
1Gigabit PCIe network card (Realtek chipset)- Supports 10/100/1000 Base-T Ethernet standard
- Supports Auto-MDI/MDI-X Auto (for crossover cable)
- Supports Jumbo Frame up to 9KBytes, Pair Swap/Polarity/Skew Correction
- Wake-on-LAN and remote wake-up
- Supports Full Duplex Flow Control (IEEE 802.3x)
- Supports IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.1Q VLAN tagging, IEEE 802.1P Layer 2 Priority Encoding
- 48KB Buffer Transmit/Receiver Chip
- Data transmission LED indicator
- Chipset: Realtek RTL8111G
The EX-6071C is a fast Gigabit Ethernet card designed for the PCI Express bus.
The EX-6071C supports a data transfer rate of up to 1000Mbit per second.
The EX-6071C supports Half and Full Duplex as well as NWay Auto-Negotation to automatically adapt to the network speed (10/100/1000 Mbit/s.).
The card is also equipped with Auto-MDI/MDI-X.
It also offers extensive support for various operating systems.
A low-profile bracket is supplied with the card for installation in a narrow PC housing.
Scope of delivery:
- EX-6071C
- Low profile bracket
- Driver CD
- manual
EXSYS EX-44388 - EXSYS PCIe Card 8S Serial RS-232 + Cable, bracket
235.23 EUR
8S PCIe serial RS-232 card incl. LP bracket (SystemBase Chip set)The EX-44388 PCI-Express I/O card provides eight serial RS-232 High Performance UART 16C1050 outputs. It has been developed to expand eight additional serial ports for PC, small workstation or server via the PCI Express bus. The card is fully PCI-Express plug-and-play compatible and has no problems with IRQ and I/O address conflicts. In addition, +5V or +12V can be configured on pin 9 of the serial connector for a POS system (Power over System). With the EX-44388 a low profile bracket is supplied so that the card can also be installed in a narrow PC housing.
- Interface: RS-232 V.24 with FIFO Buffer 16C1050 with 256Byte
- ±15kV IEC1000-4-2 ESD protection for RS232 I/OS
- I/O addresses and interrupt are assigned by the operating system, IRQ sharing
- PCIe interface compatible with 1.0a to 3.0 specifications
- Data Bits: 5, 6, 7, 8
- Stop Bits: 1, 1.5, 2
- Parity: none, even, odd, space, mark
- Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- Supports RTS/CTS and XON/XOFF Flow Control
- Supports +5V or+12V on pin 9 of the serial connectors
- Chip set: SystemBase SB16C1058PCI
Drivers: See Operating Systems
Operating system: Win98, me, 2000/XP/Vista/7/8.x/10 (32&64) Sever 200x & 2012R2, SCO-Unix, Linux 2.4 or higher
Scope of delivery: EX-44388, Octopus cable, LP bracket, driver CD, manual
EXSYS EX-44064 - EXSYS PCIe Card 4S Serial RS-232, Chip set
113.26 EUR
4S PCIe Serial RS-232 Card (SystemBase Chip set)The EX-44064 PCI-Express I/O card provides four RS-232 High Performance Serial UART 16C1050 outputs. It has been developed to expand four additional serial ports for PC, small workstation or server via the PCI Express bus. The card is fully PCI-Express plug-and-play compatible and has no problems with IRQ and I/O address conflicts. In addition, +5V or +12V can be configured on pin 9 of the serial connector for a POS system (Power over System).
- Interface: RS-232 V.24 with FIFO Buffer 16C1050 with 256Byte
- ±15kV IEC1000-4-2 ESD protection for RS232 I/OS
- I/O addresses and interrupt are assigned by the operating system, IRQ sharing
- PCIe interface compatible with 1.0a to 3.0 specifications
- Data Bits: 5, 6, 7, 8
- Stop Bits: 1, 1.5, 2
- Parity: none, even, odd, space, mark
- Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- Supports RTS/CTS and XON/XOFF Flow Control
- Supports +5V or+12V on pin 9 of the serial connectors
- Chip set: SystemBase SB16C1054PCI
Drivers: Win 2000/XP/Vista/7/8.x/10 (32&64) Sever 200x & 20xx, SCO-Unix, Linux 2.4 or higher
Operating System: According To Driver
Scope of delivery: EX-44064, 1 x slot adapter with 2 x 9 pin serial, driver CD, manual
EXSYS EX-6081POE - Network card, PCI Express, 2.5 Gigabit Ethernet, 1x RJ45
113.26 EUR
1 port 2.5Gigabit LAN PCIe card PoE incl. LP bracket (Realtek chipset)- Supports 10/100/1000/2500 Base-T Ethernet standard
- Supports 1-line 2.5/5Gbps PCI Express bus
- Fully compatible with IEEE 802.3af PoE (PSE Type 1 = 15.40W and
- IEEE 802.3af PoE+ (PSE) Type 2 = 34.20W
- Maximum power output (PD): Type 1 = 15.4W / Type 2 = 30.0W
- Fully compatible with PCI Express version 2.1
- Supports 2.5G Lite (1G data transfer rate) mode
- Supports Jumbo Frame up to 16KBytes, Pair Swap/Polarity/Skew Correction
- Auto-negotiation with Extended Next Page (XNP) capability
- Supports Auto-MDI/MDI-X Auto (for crossover cable)
- Hardware ECC and CRC function
- Supports IEEE 802.3az-2010 Energy Efficient Ethernet (EEE)
- Microsoft NDIS5, NDIS6 (IPv4, IPv6, TCP, UDP) Support of checksums and segmentation task offload (Large Send and Giant Send)
- Supports IEEE 802.1P Layer 2 Priority Encoding, IEEE 802.1Q VLAN and IEEE 802.1ad Double VLAN
- Compatible with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab,
- IEEE 802.1Q VLAN tagging
- Supports Virtual Machine Queue (VMQ for Windows Server Hyper-V installed system)
- Wake-on-LAN and 'RealWoW! technology (remote wake-up)
- LED indicator for data transmission mode
- Chipset: Realtek RTL8125B
The EX-6081PoE is a 2.5 Gigabit Ethernet card designed for the PCIe bus.
It supports Power over Ethernet and a data transfer rate of up to 2.5Gbit per second.
The EX-6081PoE supports Half and Full Duplex as well as NWay Auto-Negotation to automatically adapt to the network speed (10/100/1000/2500 Mbit/s.).
The card is also equipped with Auto-MDI/MDI-X.
It also offers extensive support for various operating systems.
Any PoE-capable end devices can be connected to the EX-6081PoE without additional PoE switches.
A low-profile bracket is supplied with the card for installation in a narrow PC housing.
Scope of delivery:
- EX-6081PoE
- Low profile bracket
- Driver CD
- User manual
STARTECH.COM ST 21050-PC-2 - 2-port PCI Express serial card, RS232, low profile
87.42 EUR
- PCIE TO SERIAL: Connect serial RS232 (DB9) devices to a computer with this low-profile serial PC card. Support for the 16C1050 UART with high performance. Activity display via LED status lights on the DB9 card
- DEVICE COMPATIBILITY: Use this serial card to connect barcode readers/scanners, receipt printers, scales, PLCs, medical devices etc. The UART PCIe card operates with a 5-V or 12-V current via pin 9. Full-profile bezel is included
- APPLICATIONS: This card is ideal for IT applications such as server rooms, industrial control/automation, logistics and laboratories. With this RS232 PCIe card you can continue to use your old devices. The DB9 connector supports screw fastening
- DUAL SERIAL CARD SPECIFICATIONS: 16C1050 UART. Max. baud rate 921.6 Kbps per port. 256-byte FIFO. COM retention. Windows and Linux. ASIX AX99100 chipset. Odd/Even/Mark/Space/None parity modes. 5/6/7/8/9 data bits. PCIe 2.0 x1. Full-profile bezel included
DELOCK 90006 - PCI Express Card to 1 x Serial RS-232
30.57 EUR
The PCI Express card by Delock expands a PC by one external serial port. Different devices such as scanner, protocol converter, IoT devices etc. can be connected to this card.Low Profile Form Factor
By using the included low profile bracket, the PCI Express card can be also installed into a Mini-PC.
• Connectors:
external: 1 x serial RS-232 DB9 male
internal: 1 x PCI Express x1, V2.0
• Chipset: ASIX AX99100
• Compatible with 16C950 UART
• Supports Active State Power Management (ASPM)
• Supports Direct Memory Access (DMA)
• Data transfer rate up to 921.6 Kbps
• FIFO: 256 byte
• Databits: 5, 6, 7, 8, 9
• Stop bits: 1, 1.5, 2
• Parity: even, odd, none, mark, space
• Flow control: none, hardware RTS / CTS, software XON / XOFF
• Operating temperature: 0 °C ~ 70 °C
System requirements
• Linux Kernel 2.6.24 or above
• Windows 8.1/8.1-64/10/10-64
• PC with one free PCI Express slot
Package content
• PCI Express card
• Low profile bracket
• Driver CD
• User manual
DELOCK 89918 - PCI Express Card > 2 x Serial RS-232
33.16 EUR
The PCI Express card by Delock expands a PC by two external serial RS-232 ports. Different devices such as scanner, protocol converter, IoT devices etc. can be connected to this card. By using the included low profile brackets, the PCI Express card can be also installed into a Mini-PC.Specification
• Connectors:
external: 2 x serial RS-232 DB9 male
internal: 1 x PCI Express x1, V1.1
• Chipset: WCH CH382L
• Compatible with 16C550 UART
• Buffer: 256 byte on each port
• Databits: 5, 6, 7, 8
• Stop bits: 1, 2
• Parity: even, odd, none, mark, space
• Flow control: none, hardware RTS / CTS, software XON / XOFF
System requirements
• Windows 7/7-64/8.1/8.1-64/10/10-64, ex Linux Kernel 4.15
• PC with one free PCI Express slot
Package content
• PCI Express card
• 2 x low profile bracket
• Driver CD
• User manual
Package
• Retail Box
DELOCK 89555 - Delock PCI Express Card > 2 x Serial RS-232
35.38 EUR
The PCI Express card by Delock expands a PC by two external serial ports. Different devices such as scanner, printer, mouse etc. can be connected to this card. By using the included low profile brackets, the PCI Express card can be also installed into a Mini-PC.Specification
• Connector:
external: 2 x serial RS-232 DB9 male
internal: 1 x PCI Express x1, V2.0
• Chipset: ASIX AX99100
• Data transfer rate up to 230.4 Kb/s
• FIFO: 256 byte
• Compatible with 16C950 UART
System requirements
• Windows 7/7-64/8.1/8.1-64/10/10-64
• PC with one free PCI Express slot
Package content
• PCI Express card
• 2 x low profile bracket
• Driver CD
• User manual
Package
• Retail Box
DELOCK 89948 - PCI Express Card to 1 x Serial RS-232
30.57 EUR
DescriptionThe PCI Express card by Delock expands a PC by one external serial RS-232 port. Devices such as scanners, protocol converters, POS systems, infrared -, IoT - devices etc. and different modes can be used. By using the included low profile brackets, the PCI Express card can be also installed into a Mini-PC.
Specification
- Connectors:
1 x serial RS-232 DB9 male
1 x PCI Express x1, V2.0 - Chipset: ASIX AX99100
- Compatible with 16C950 UART
- Supports Active State Power Management (ASPM)
- Supports Direct Memory Access (DMA)
- Modes
Supports slow IrDA mode up to 115 Kbps
Supports Multi-Drop 9-bit mode - Data transfer rate up to 230.4 Kb/s
- FIFO: 256 byte
- Databits: 5, 6, 7, 8, 9
- Stop bits: 1, 1.5, 2
- Parity: even, odd, none, mark, space
- Flow control: none, hardware RTS / CTS, software XON / XOFF
- Operating temperature: 0 °C ~ 55 °C
- Relative humidity: 10 - 90 %
- Dimensions (LxWxH): ca. 64 x 60 x 16 mm
System requirements
- Windows 7/7-64/8.1/8.1-64/10/10-64
- PC with one free PCI Express slot
Package content
- PCI Express card
- 1 x low profile bracket
- Driver CD
- User manual
Package
- Retail Box
DELOCK 89333 - PCI Express card > 1 x serial RS-232 HS
53.67 EUR
Delock PCI Express card > 1 x serial RS-232 High Speed 921K with power supplyThe Delock PCI Express card expands your system by one external high-speed RS-232 port. Use this card for applications such as recording measured values, machine control, automation, development or communication. The comprehensive surge protection and extended temperature range also make this card suitable for use in the industrial sector. Connected devices can be supplied with a voltage of 5 V or 12 V.
Technical data
• Chipset: Exar 17V352
• Connections:
External:
1 x serial RS-232 Sub-D 9-pin plug
Internal:
1 x PCI Express x1, V2.0
1 x 4-pin Molex power connector
• Baud rate: up to 921.6 Mb/s
• Compatible with 16C550 UART
• 256 Byte FIFO
• Data bits: 5, 6, 7, 8
• Stop bits: 1, 1.5, 2
• Parity: none, even, odd, space, mark
• Flow control: RTS/CTS, XON/XOFF
• Adjustable power supply 5 V/12 V or RI on pin 9
• Additional 5-V/12-V power supply possible via pin 1
depending on the connected device
• Operating temperature: -30°C - +75°C
• Storage temperature: -40°C - +85°C
• Relative humidity up to 95% (non-condensing)
• 15-kV ESD protection for all signals
• I/O addresses and IRQ are assigned by the system
System requirements
• Windows XP/XP-64/Vista/Vista-64/7/7-64, Linux from Kernel 2.6
• PC with one free PCI Express slot
• Power supply unit with one free Molex power connector
Package contents
• PCI Express card
• Low profile trim
• CD driver
• User manual
Packaging
• Box
DELOCK 90007 - PCI Express Card to 2 x Serial RS-232
29.54 EUR
The PCI Express card by Delock expands a PC by two external serial RS-232 ports. Different devices such as scanner, protocol converter, IoT devices etc. can be connected to this card.Low Profile Form Factor
By using the included low profile brackets, the PCI Express card can be also installed into a Mini-PC.
• Connectors:
external: 2 x serial RS-232 DB9 male
internal: 1 x PCI Express x1, V1.1
• Chipset: WCH CH382L
• Compatible with 16C550 / 16C750 UART
• Data transfer rate up to 921.6 Kbps
• Buffer: 256 byte on each port
• Databits: 5, 6, 7, 8
• Stop bits: 1, 2
• Parity: even, odd, none, mark, space
• Flow control: none, hardware RTS / CTS, software XON / XOFF
• Operating temperature: -20 °C ~ 80 °C
System requirements
• Linux Kernel 4.15 or above
• Windows 8.1/8.1-64/10/10-64
• PC with one free PCI Express slot
Package content
• PCI Express card
• 2 x low profile bracket
• Driver CD
• User manual
Package
• Retail Box
EXSYS EX-6072-3 - Network card, PCI Express, Gigabit Ethernet, 2x RJ45
82.25 EUR
The EX-6072-3 is a high performance Dual Gigabit LAN to PCI-Express Card which is fully compatible with IEEE 802.3/u/ab. It is specially designed for any PC with a PCI-Express slot. With the EX-6072-3 you can upgrade your Ethernet LANs to the speed of 1000Mbps on each port, that’s up to 10 times faster than the standard high speed Ethernet. It will supercharge your data transfer on your local network and improve your bandwidth. It provides a big transmit/receive buffer, crossover detection and auto-correction. It is fully plug-and-play compatible to install it easily and quickly and does support a various range of operating systems. With the card it’s included a Low Profile Bracket for small computer case.- Support 10/100/1000 Base-T Ethernet standards
- Support Auto-MDI/MDI-X Auto (for Crossover cable)
- Support Jumbo Frame up to 9Kbytes, Pair Swap/Polarity/Skew Correction
- Wake-on-LAN and Remote Wake-up
- Support Full Duplex Flow Control (IEEE 802.3x)
- Support IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.1Q VLAN tagging, IEEE 802.1P Layer 2 Priority Encoding
- 48KB Buffer Transmit/Receiver Chip
- Activity LED to check the data transfer
EXSYS EX-42034IS - PCI card to 4x serial RS-232/422/485, opt. ISO.
61.58 EUR
- INTERFACE: RS-232 V.24 / RS-422 / RS-485
- 15 kV ESD over-voltage protection and 4.0 kV optical isolation
- ±15kV IEC1000-4-2 ESD protection for RS232 I/O.
- FIFO buffer: 16C550 with 16 bytes
- I/O addresses and interrupt are assigned by the operating system
- Data bits: 5, 7, 7, 8/stop bits: 1, 1.5, 2
- Parity: none, even, odd, space and mark
- Supports ATTATM Auto Transmitter
- Terminal: 120 ohms, can be switched on or off
- Signals:
- Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- RS-422 - 4 wire (TxD+/-, RxD+/-) full duplex
- RS-485 - 4 wire (TxD+/-, RxD+/-) full duplex
- RS-485: two-wire - Data+, Data- and GND
- Chip set: FTDI
The EX-42034IS PCI I/O card provides four serial RS-232, 422 and 485 High Performance UART 16C550 outputs with 15KV ESD overvoltage protection and 2.5KV optical isolation. It was developed to add eight additional serial outputs for a PC, workstation or server via the PCI or PCI-X bus.
It supports the ATTATM Auto RS-485 Transmitter features. The RS-232, 422 or 485 transmission type can be set individually for each port. POS is not adjustable.
EXSYS EX-42034 - PCI card to 4x serial RS-232/422/485
154.6 EUR
- INTERFACE: RS-232 V.24 / RS-422 / RS-485
- ±15kV IEC1000-4-2 ESD protection for RS232 I/O.
- FIFO buffer: 16C550 with 16 bytes
- I/O addresses and interrupt are assigned by the operating system
- Data bits: 5, 7, 7, 8/stop bits: 1, 1.5, 2
- Parity: none, even, odd, space and mark
- Supports ATTA Auto Transmitter
- Terminal: 120 ohms, can be switched on or off
- Signals:
- Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- RS-422 - 4 wire (TxD+/-, RxD+/-) full duplex
- RS-485 - 4 wire (TxD+/-, RxD+/-) full duplex
- RS-485: two-wire - Data+, Data- and GND
- Chip set: FTDI
The EX-42034 PCI I/O card provides four serial RS-232 high-performance UART 16C550 outputs. It was developed to add four additional serial outputs for a PC, small workstation or server via the PCI or PCI-X bus. Can be configured +5 V and +12 V on pin 9 of the serial connector for a POS system (power over system).
The card is fully plug-and-play compatible. It supports the ATTATM Auto RS-485 Transmitter features. The RS-232, 422 or 485 transmission type can be set individually for each port.
EXSYS EX-42374 - PCI card to 4x serial RS-232/422/485
175.28 EUR
- Interface: 4 x RS-232 V.24, RS-422/485
- FIFO buffer: 16C1050 with 256 bytes
- I/O addresses and interrupt: assigned by the system BIOS, IRQ sharing
- Data bits: 5, 6, 7, 8/stop bits: 1, 1.5, 2
- Parity: none, even, odd, space, mark
- Signals RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- RS-422 signals - 4 wire (TXD+/-, RXD+/-) (full duplex)
- RS-485 - 4 wire (TXD+/-, RXD+/-) (full duplex)
- RS-485 - 2 wire (Data+/-, Data+/-) (half duplex)
- Supports ATTATM Auto Transmitter
- RS-422/485 termination - 120 ohms can be switched on or off
- Supports 5-V and 3.3-V motherboards
- Chip set: SystemBase SB16C1054PCI
The EX-42374 PCI I/O card provides 4 serial RS-232, 422 and 485 high-performance UART 16C1050 outputs. It was developed to add 4 additional serial combo ports for PCs, small workstations or servers via the PCI bus. The card is fully PCI or PCI-X plug and play compatible and has no problems with IRQ and I/O address conflicts. It supports ATA TM Auto RS-485 Transmitter features. In addition, +5 V or +12 V can be configured on pin 9 for a POS system (power over system).
EXSYS EX-44384 - EXSYS PCIe Card 4S Serial RS-232 + Cable, bracket
142.2 EUR
4S PCIe serial RS-232 card incl. LP bracket (SystemBase Chip set)The EX-44384 PCI-Express I/O card provides four RS-232 High Performance Serial UART 16C1050 outputs. It has been developed to expand four additional serial ports for PC, small workstation or server via the PCI Express bus. The card is fully PCI-Express plug-and-play compatible and has no problems with IRQ and I/O address conflicts. In addition, +5V or +12V can be configured on pin 9 of the serial connector for a POS system (Power over System). With the EX-44384 a low profile bracket is supplied so that the card can also be installed in a narrow PC housing.
- Interface: RS-232 V.24 / FIFO Buffer: 16C1050 with 256Byte
- ±15kV IEC1000-4-2 ESD protection for RS232 I/OS
- I/O addresses and interrupt are assigned by the operating system, IRQ sharing
- PCIe interface compatible with 1.0a to 3.0 specifications
- Data Bits: 5, 6, 7, 8
- Stop Bits: 1, 1.5, 2
- Parity: none, even, odd, space, mark
- Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
- Supports hardware and software flow control
- Supports +5V or+12V on pin 9 of the serial connectors
- Chip set: SystemBase SB16C1054PCI
DELOCK 90000 - PCI Express Card to 1 x Serial RS-232
41.94 EUR
The Delock PCI Express card expands a PC by one external serial port. Different devices such as scanner, printer, mouse etc. can be connected to this card. By using the included low profile bracket, the PCI Express card can be also installed into a Mini-PC.• Connectors:
external: 1 x serial RS-232 DB9 male
internal: 1 x PCI Express x1, V2.0
• Chipset: Exar XR17V352
• Data transfer rate up to 230.4 Kbps
• FIFO: 256 byte
• Compatible with 16C550 UART
• Databits: 5, 6, 7, 8
• Stop bits: 1, 1.5, 2
• Parity: even, odd, none, mark, space
• Flow control: none, hardware RTS / CTS, software XON / XOFF
• Dimensions (LxW): ca. 64 x 45 mm
System requirements
• Windows 8.1/8.1-64/10/10-64
• PC with one free PCI Express slot
Package content
• PCI Express card
• Low profile bracket
• Driver CD
• User manual
Package
• Retail Box
DIGITUS 30000-1 - PCI Express card for 2x RS-232
35.69 EUR
Serial I/O,2-port, PCIexpress add-on card 2xDB9 M, slot sheet + LP sheet, ASIX99100 chipset - Data transfer rate up to 128,000 bps
- Complies with PCI Express Base specification 2.0
- 2x DSUB 9, serial interfaces, male, UART 16C950
This serial PCI Express add-on card can be inserted into its PCI Express slot and is provided with two RS232 (DB9) serial ports. Based on a native single-chip design, it reduces CPU load by up to 48% compared to traditional serial cards.
Technical details
- 2x DSUB 9, serial interfaces, male, UART 16C950
- Chipset: AX99100
- Data transfer rate up to 1.5 Mbps
- Complies with PCI Express Base specification 2.0
- Compatible with PCI Power Management 1.2
- Operating temperature: 0°C to 70°C
- Operating humidity: 0% - 85% RH (non condensing)
- Supports Windows 10, 8.1, 8, 7, Vista, XP, macOS and Linux
Included in delivery
- Serial interface card, PCIe
- Low-profile slot panel
- User manual
- CD driver
STARTECH.COM ST 11050-PC-SERI - 1-port PCI Express serial card, RS232
71.92 EUR
- PCIE TO SERIAL: Connect a serial RS232 (DB9) device to a computer with this serial PC card. Support for the 16C1050 UART with high performance. Monitor activity with the built-in LED status lights on the PCI Express DB9 card
- DEVICE COMPATIBILITY: Use this serial card to connect barcode readers/scanners, receipt printers, scales, PLCs, medical devices etc. The UART PCIe card operates with a 5-V or 12-V current via pin 9. Low-profile bezel is included
- APPLICATIONS: This card is ideal for IT applications such as server rooms, industrial control/automation, logistics and laboratories. With this RS232 PCIe card you can continue to use your old devices. The DB9 connector supports screw fastening
- SPECIFICATIONS: 1 port 16C1050 UART Max. baud rate 921.6 Kbps 256-byte FIFO COM retention Supports Windows and Linux Asix AX99100 chipset Odd/Even/Mark/Space/None parity modes 5/6/7/8/9 data bits PCIe 2.0 x1 Low-profile bezel included