ADA FB M0 BP - Development boards - Adafruit Feather M0 Basic Proto
33 EUR
Explore the detailed sheet rich in complete information, compare prices and identify the features of PRODUCTNAME, available at the cost of PRICE CURRENCY; belongs to the CATEGORY NAME; the seller is SELLER NAME and the manufacturer is MANUFACTURER NAME.
"The Adafruit Feather are a complete line of development boards from Adafruit that are both standalone and stackable. They're able to be powered by lipo batteries for on-the-go use or by their micro-USB plugs for stationary projects. Feathers are flexible, portable, and as light as their namesake.
At the Feather M0's heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip.
Dimension: 51 x 23 x 8mm
The Feather M0 Basic Proto has some extra space left over, so we give you a tiny little prototyping area. If you just need to attach a button or sensor, you may be able to skip out on a breadboard and wire it directly on there.
Comes fully assembled and tested, with a USB bootloader that lets you quickly use it with the Arduino IDE. We also toss in some header so you can solder it in and plug into a solderless breadboard. Lipoly battery and USB cable not included (but we do have lots of options in the shop if you'd like!)"
Delivery Cost: 9.95 EUR
Availability: in stock
Delivery Time: 4-5 business days
Condition: new
"The Adafruit Feather are a complete line of development boards from Adafruit that are both standalone and stackable. They're able to be powered by lipo batteries for on-the-go use or by their micro-USB plugs for stationary projects. Feathers are flexible, portable, and as light as their namesake.
At the Feather M0's heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip.
- ATSAMD21G18 @ 48 MHz with 3.3 V logic/power
- 256 KB of FLASH + 32 KB of RAM
- No EEPROM
- 32.768 KHz crystal for clock generation & RTC
- 3.3 V regulator with 500 mA peak current output
- USB native support, comes with USB bootloader and serial port debugging
- 20x GPIO
- Hardware Serial, hardware I2C, hardware SPI support
- PWM outputs on all pins
- 6x 12-bit analog inputs
- 1x 10-bit analog ouput (DAC)
- Built in 100 mA lipoly charger with charging status indicator LED
- red LED for general purpose blinking
- 4 mounting holes
- Reset button
The Feather M0 Basic Proto has some extra space left over, so we give you a tiny little prototyping area. If you just need to attach a button or sensor, you may be able to skip out on a breadboard and wire it directly on there.
Comes fully assembled and tested, with a USB bootloader that lets you quickly use it with the Arduino IDE. We also toss in some header so you can solder it in and plug into a solderless breadboard. Lipoly battery and USB cable not included (but we do have lots of options in the shop if you'd like!)"
Delivery Cost: 9.95 EUR
Availability: in stock
Delivery Time: 4-5 business days
Condition: new
Comparison of Similar Products
ADA TRKT 5V - Development boards - Adafruit Trinket 5V
18.63 EUR
"The Trinket is small, but do not be fooled by its size! It's a tiny microcontroller board, built around the Atmel ATtiny85, a little chip with a lot of power. Adafruit wanted to design a microcontroller board that was small enough to fit into any project, and low cost enough to use without hesitation. Perfect for when you don't want to give up your expensive dev-board and you aren't willing to take apart the project you worked so hard to design. It's Adafruit lowest-cost arduino-IDE programmable board!The Attiny85 is a fun processor because despite being so small, it has 8K of flash, and 5 I/O pins, including analog inputs and PWM 'analog' outputs. We designed a USB bootloader so you can plug it into any computer and reprogram it over a USB port just like an Arduino. In fact we even made some simple modifications to the Arduino IDE so that it works like a mini-Arduino board. You can't stack a big shield on it but for many small & simple projects the Trinket will be your go-to platform.
Trinket does not have a Serial port connection for debugging so the serial port monitor will not be able to send/receive data
- ATtiny85 on-board, 8K of flash, 512 byte of SRAM, 512 bytes of EEPROM
- Internal oscillator runs at 8MHz, but can be doubled in software for 16MHz
- USB bootloader with a nice LED indicator
- Micro-USB jack for power and/or USB uploading
- ~5.25K bytes available for use (2.75K taken for the bootloader)
- Power with either USB or external output (such as a battery)
- On-board green power LED and red pin #1 LED
- Reset button for entering the bootloader or restarting the program
- 5x GPIO
- Hardware I2C / SPI capability for breakout & sensor interfacing.
- Mounting holes
- Dimensions: 31 x 15.5 x 5 mm "
ADA CIRCUIT - Development boards - Adafruit Circuit Playground Classic
33 EUR
"Would you like to learn electronics, with an all-in-one board that has sensors and LEDs built in? Circuit Playground is here - and it's the best way to practice programming on real hardware with no soldering or sewing required!Circuit Playground features an ATmega32u4 processor, just like our popular Flora. The board's also round and has alligator-clip pads around it so you don't have to solder or sew to make it work. You can power it from USB, a AAA battery pack, or with a Lipoly battery (for advanced users). Just program your code into the board then take it on the go!
- ATmega32u4 Processor, running at 3.3 V and 8 MHz
- MicroUSB port for programming and debugging with Arduino IDE
- USB port can act like serial port, keyboard, mouse, joystick or MIDI
Circuit Playground has built-in USB support. Built in USB means you plug it in to program it and it just shows up. All you really need is a Micro-B data/sync USB cable - not included! With the new 1.6.4+ Arduino IDE, it takes only a few seconds to add support.
- 10 x mini NeoPixels, each one can display any color
- 1 x Motion sensor (LIS3DH triple-axis accelerometer with tap detection, free-fall detection)
- 1 x Temperature sensor (thermistor)
- 1 x Light sensor (phototransistor)
- 1 x Sound sensor (MEMS microphone)
- 1 x Mini speaker (magnetic buzzer)
- 2 x Push buttons, left and right
- 1 x Slide switch
- 8 x alligator-clip friendly input/output pins
- Includes I2C, UART, and 4 pins that can do analog inputs/PWM output
- All 8 pads can act as capacitive touch inputs
- Green ""ON"" LED so you know its powered
- Red ""#13"" LED for basic blinking
- Reset button
ADA FB 32U4 BFLE - Development boards - Adafruit Feather 32u4 Bluefruit LE
44.58 EUR
"The Adafruit Feather are a complete line of development boards from Adafruit that are both standalone and stackable. They're able to be powered by lipo batteries for on-the-go use or by their micro-USB plugs for stationary projects. Feathers are flexible, portable, and as light as their namesake.- ATmega32u4 @ 8 MHz with 3.3 V logic / power
- 3.3 V regulator with 500 mA peak current output
- USB native support, comes with USB bootloader and serial port debugging
- 20x GPIO
- Hardware Serial, hardware I2C, hardware SPI support
- 8x PWM pins
- 10x analog inputs
- Built in 100mA lipoly charger with charging status indicator LED
- red LED for general purpose, blinking
- 4 mounting holes
- Reset button
- 51.2 x 22.8 x 8 mm
Built-in nRF51822 Bluetooth Low Energy module"
ADAFRUIT DEBO FEATHER RTC - Development boards - Adalogger FeatherWing, RTC + SD-Addon
22.3 EUR
"The Adafruit Feather are a complete line of development boards from Adafruit that are both standalone and stackable. They're able to be powered by lipo batteries for on-the-go use or by their micro-USB plugs for stationary projects. Feathers are flexible, portable, and as light as their namesake.This FeatherWing will make it real easy to add datalogging to any of our existing Feathers. You get both an I2C real time clock (PCF8523) with 32KHz crystal and battery backup, and a microSD socket that connects to the SPI port pins (+ extra pin for CS). A CR1220 coin cell is required to use the RTC battery-backup capabilities!
- 50.8 x 22.9 x 1.6 mm
ADA FB M0 A - Development boards - Adafruit Feather M0 Adalogger
33.62 EUR
"The Adafruit Feather are a complete line of development boards from Adafruit that are both standalone and stackable. They're able to be powered by lipo batteries for on-the-go use or by their micro-USB plugs for stationary projects. Feathers are flexible, portable, and as light as their namesake.This is the Adafruit Feather M0 Adalogger - our take on an 'all-in-one' Cortex M0 datalogger (or data-reader) with built in USB and battery charging. Its an Adafruit Feather M0 with a microSD holder ready to rock! We have other boards in the Feather family, check'em out here
At the Feather M0's heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip.
- ATSAMD21G18 @ 48 MHz with 3.3 V logic/power
- 256 kB of FLASH + 32 kB of RAM
- No EEPROM
- 3.3V regulator with 500mA peak current output
- USB native support, comes with USB bootloader and serial port debugging
- 20x GPIO
- Hardware Serial, hardware I2C, hardware SPI support
- 8x PWM pins
- 10x analog inputs
- Built in 100mA lipoly charger with charging status indicator LED
- red LED for general purpose blinking
- 4 mounting holes
- Reset button
- with green LED for your blinking pleasure
- with MicroSD card holder for adding as much storage as you could possibly want, for reading or writing
- Dimensions: 23 x 51 x 8 mm
ADAFRUIT DEBO FW OLED ADD - Developer Boards - FeatherWing OLED Addon, SSD1306
26.95 EUR
"The Adafruit Feather are a complete line of development boards from Adafruit that are both standalone and stackable. They're able to be powered by lipo batteries for on-the-go use or by their micro-USB plugs for stationary projects. Feathers are flexible, portable, and as light as their namesake.Technical Details
- FeatherWing OLED - 128x32 OLED Add-on For All Feather Boards
- very readable due to the high contrast of an OLED display
- dimensions: 22.9 x 50.9 mm
- Display area: 25.8 mm
ADA FB HUZZAH - Development boards - Adafruit Feather HUZZAH
29.54 EUR
"The Adafruit Feather are a complete line of development boards from Adafruit that are both standalone and stackable. They're able to be powered by lipo batteries for on-the-go use or by their micro-USB plugs for stationary projects. Feathers are flexible, portable, and as light as their namesake.- ESP8266 @ 80 MHz with 3.3 V logic/power
- 4 MB of FLASH (32 MBit)
- Built in WiFi 802.11 b/g/n
- 3.3 V regulator with 500mA peak current output
- CP2104 USB-Serial converter onboard/li>
- Auto-reset support for getting into bootload mode before firmware upload
- 9x GPIO pins - can also be used as I2C and SPI
- 1x analog inputs 1.0 V max
- Built in 100mA LiPoly charger with charging status indicator LED, can also cut a trace to disable the charger
- Pin #0 red LED for general purpose blinking. Pin #2 blue LED for bootloading debug & general purpose blinking
- Power/enable pin
- 4 mounting holes
- Reset button
ADA GEMMA 2 - Development boards - Adafruit GEMMA V2
22.3 EUR
"GEMMA is a tiny wearable platform board with a lot of might. Powered by a Attiny85 and programmable with an Arduino IDE over USB, you'll be able to realize any wearable project!The Attiny85 is a fun processor because despite being so small, it has 8K of flash, and 5 I/O pins, including analog inputs and PWM 'analog' outputs. Adafruits designed a USB bootloader so you can plug it into any computer and reprogram it over a USB port just like an Arduino (it uses 2 of the 5 I/O pins, leaving you with 3). In fact Adafruit even made some simple modifications to the Arduino IDE so that it works like a mini-Flora. Perfect for small & simple projects the GEMMA will be your go-to wearable electronics platform.
- GEMMA does not have a Serial port connection for debugging
- super small, only 1.1"" / 28 mm diameter and 0.28"" / 7 mm thick
- easy-to-sew or solder pads for embedding in your wearable project
- ATtiny85 on-board
- 8 kB of flash
- 512 byte of SRAM
- 512 bytes of EEPROM
- Internal oscillator runs at 8MHz
- Ultra low power, draws only 9 mA while running
- USB bootloader with a LED indicator
- Micro-USB jack for power and / or USB uploading
- 5.25 kB available for use (2.75 kB taken for the bootloader)
- 3.3 V power regulator with 150 mA output capability and ultra-low dropout
- Power with either USB or external output (such as a battery)
- green power LED and red pin #1 LED
- Reset button for entering the bootloader or restarting the program
- 3x GPIO
- I2C capability
- Dimensions: 28 mm x 7 mm
ADA TRKT PRO 3V - Development boards - Adafruit Pro Trinket 3 V
23.7 EUR
"The Pro Trinket combines everything you love about Trinket with the familiarity of the core Arduino chip, the ATmega328. It's like an Arduino Pro Mini with more pins and USB tossed in.The Pro Trinket has 18 GPIO, 2 extra analog inputs, 28 kB of flash, and 2 kB of RAM.
Like the Trinket, it has onboard USB bootloading support, so you can either program your Pro Trinket over USB or with a FTDI cable just like the Pro Mini and friends.
The Pro Trinket PCB measures only 38 x 18 x 5 mm (without headers) but packs the same capability as an Arduino UNO. So it's great once you've finished up a prototype on an official Arduino UNO and want to make the project smaller.
- Pins #2 and #7 are not available (they are exclusively for USB)
- The Pro Trinket 3V runs at 12MHz, this doesn't affect most projects
- The onboard power supply is a 3.3V regulator and it can provide 150mA output
- You cannot plug shields directly into the Pro Trinket
- There is no Serial-to-USB chip onboard
- The bootloader on the Pro Trinket use 4 kB of FLASH
Here's some handy specifications:
- ATmega328P onboard chip in QFN package running at 3.3 V logic
- 12 MHz clock rate, 28 kB FLASH available
- USB bootloader with a nice LED indicator
- Also has headers for an FTDI port for reprogramming
- Micro-USB jack for power and/or USB uploading
- On-board 3.3 V power regulator with 150 mA output capability and ultra-low dropout
- Power with either USB or external output (such as a battery)
- On-board green power LED and red pin #13 LED
- Reset button for entering the bootloader or restarting the program
- Mounting holes
ADA FB M0 BFLE - Development boards - Adafruit M0 Bluefruit LE
44.58 EUR
"The Adafruit Feather are a complete line of development boards from Adafruit that are both standalone and stackable. They're able to be powered by lipo batteries for on-the-go use or by their micro-USB plugs for stationary projects. Feathers are flexible, portable, and as light as their namesake.This is the Adafruit Feather M0 Bluefruit LE - our take on an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with built in USB and battery charging. At the Feather M0's heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip.
- ATSAMD21G18 @ 48 MHz with 3.3 V logic/power
- No EEPROM
- 3.3 V regulator with 500 mA peak current output
- USB native support, comes with USB bootloader and serial port debugging
- 20x GPIO
- Hardware Serial, hardware I2C, hardware SPI support
- 8x PWM pins
- 10x analog inputs
- 1x analog output
- Built in 100 mA lipoly charger with charging status indicator LED
- red LED for general purpose blinking
- 4 mounting holes
- Reset button
The Feather M0 Bluefruit LE uses the extra space left over to add our excellent Bluefruit BTLE module + two status indicator LEDs.
The Power of Bluefruit LE
The Bluefruit LE module is an nRF51822 chipset from Nordic, programmed with multi-function code that can do quite a lot! For most people, they'll be very happy to use the standard Nordic UART RX/TX connection profile. In this profile, the Bluefruit acts as a data pipe, that can 'transparently' transmit back and forth from your iOS or Android device. You can use our iOS App or Android App, or write your own to communicate with the UART service.
The board is capable of much more than just sending strings over the air! Thanks to an easy to learn AT command set, you have full control over how the device behaves, including the ability to define and manipulate your own GATT Services and Characteristics, or change the way that the device advertises itself for other Bluetooth Low Energy devices to see. You can also use the AT commands to query the die temperature, check the battery voltage, and more, check the connection RSSI or MAC address, and tons more. Really, way too long to list here!
Use the Bluefruit App to get your project started
Using our Bluefruit iOS App or Android App, you can quickly get your project prototyped by using your iOS or Android phone/tablet as a controller. We have a color picker, quaternion/accelerometer/gyro/magnetometer or location (GPS), and an 8-button control game pad. This data can be read over BLE and piped...
ADA FB NRF52 - Adafruit nRF52 Bluefruit LE
38.84 EUR
"Adafruit Feather is a complete product line of development boards that can be operated both stand-alone and stackable. They can be powered on the road by LiPo batteries or stationary via their Micro-USB connectors. Feathers are flexible, portable and as light as a feather as their name suggests.The Adafruit Feather nRF52 Bluefruit is another easy-to-use all-in-one Bluetooth low energy Bluetooth board with a native Bluetooth chip, the nRF52832! It is the approach for an all-in-one Arduino compatible Bluetooth Low Energy with integrated USB and battery charging.
- ARM Cortex M4
- 32 bit
- Program memory: 512 kB
- 19x GPIO
- Supply voltage: 3.3 V
- dimensions: 51 x 22,9 x 7,1 mm
ADA METRO MINI - Development boards - Adafruit Metro Mini 328
31.35 EUR
"Metro Mini is a small, Breadboard friendly developer board that is easy to use and hacker friendly. It can be programmed with Arduino IDE and comes as a fully populated and tested board with boot loader and a header.- ATmega328 - This popular chip has 32 kB of flash, 2 kB of RAM, clocked at 16MHz
- Power the METRO Mini with 6 - 16 V polarity protected on the Vin pin, or plug the micro USB connector to any 5 V USB source.
- 20x GPIO
- GPIO Logic level is 5 V
- 5 V onboard regulator with 150 mA out, 3.3 V 50m A available via FTDI chip
- USB to Serial converter
- Four indicator LEDs, on the top of the PCB
- Easy reprogramming, comes pre-loaded with the Optiboot bootloader
- USB Programming and debugging
- Input voltage: 6 - 16 V (a 9 V DC power supply is recommended)
- 5 V logic with 3.3 V compatible inputs
- 20 Digital I/O Pins: 6 are also PWM outputs and 6 are also Analog Inputs
- Adafruit Black PCB with gold plate on pads
- Dimensions: 18 x 44 x 4 mm
ADAFRUIT DEBO ADA ESP8266 - Development boards - ESP8266 Breakout
20.75 EUR
"ESP8266 breakout board with WiFi module- with reset button
- red LED
- output voltage: 3.3 V
- 500 mA controller
- two diode-protected power inputs - 1x USB cable, 1x battery)
- 9x GPIO, which can also be used for I2C or SPI
- 2x UART pins
- Dimensions L x W x H 38 x 25 x 5 mm
ADA TRKT MINI - Development boards - Adafruit Trinket Mini
18.63 EUR
"Trinket may be small, but do not be fooled by its size! It's a tiny microcontroller board, built around the Atmel ATtiny85, a little chip with a lot of power. We wanted to design a microcontroller board that was small enough to fit into any project, and low cost enough to use without hesitation. Perfect for when you don't want to give up your expensive devboard and you aren't willing to take apart the project you worked so hard to design. It's our lowest-cost arduino-IDE programmable board!The Attiny85 is a fun processor because despite being so small, it has 8K of flash, and 5 I/O pins, including analog inputs and PWM 'analog' outputs. We designed a USB bootloader so you can plug it into any computer and reprogram it over a USB port just like an Arduino. In fact we even made some simple modifications to the Arduino IDE so that it works like a mini-Arduino board. You can't stack a big shield on it but for many small & simple projects the Trinket will be your go-to platform.
- ATtiny85
- 8 kB of flash
- 512 byte of SRAM
- 512 bytes of EEPROM
- Internal oscillator runs at 8MHz, but can be doubled in software for 16MHz
- USB bootloader with LED indicator
- mini or microUSB jack for power and / or USB uploading
- 5.25 kB available for use (2.75 kB taken for the bootloader)
- Power with either USB or external output (such as a battery)
- On-board green power LED and red pin #1 LED
- Reset button for entering the bootloader or restarting the program
- 5x GPIO
- I2C / SPI capability
- with mounting holes
ADAFRUIT ADA BLE UART - Development boards - Bluefruit LE-UART-Friend
30.21 EUR
"The Bluefruit LE UART Friend makes it easy to add Bluetooth Low Energy connectivity to anything with a hardware or software serial port. Adafruit even have nice hardware flow control so you won't have to think about losing data. Connect to your Arduino or other microcontroller or even just a standard FTDI cable for debugging and testing.This multi-function module can do quite a lot! For most people, they'll be very happy to use the standard Nordic UART RX/TX connection profile. In this profile, the Bluefruit acts as a data pipe, that can 'transparently' transmit back and forth from your iOS or Android device. You can use our iOS App or Android App, or write your own to communicate with the UART service.
So it's a fancy pants Wireless UART Adapter?
The board is capable of much more than just sending strings over the air! Thanks to an easy to learn AT command set, you have full control over how the device behaves, including the ability to define and manipulate your own GATT Services and Characteristics, or change the way that the device advertises itself for other Bluetooth Low Energy devices to see. You can also use the AT commands to query the die temperature, check the battery voltage, and more, check the connection RSSI or MAC address, and tons more.
Using the Bluefruit iOS App or Android App, you can quickly get your project prototyped by using your iOS or Android phone/tablet as a controller.
Technical Details
- ARM Cortex M0 core running at 16MHz
- 256KB flash memory
- 32KB SRAM
- Transport: UART @ 9600 baud with HW flow control (CTS+RTS required)
- 5V-safe inputs (Arduino Uno friendly, etc.)
- On-board 3.3V voltage regulation
- Bootloader with support for safe OTA firmware updates
- Easy AT command set to get up and running quickly
- Dimensions: 21mm x 32mm x 5mm / 0.8"" x 1.26"" x 0.2""
- Weight: 3.4g