REICHELT IE: Small household appliance accessories
The Best
AEG U5 - AEG U5 hot water cylinder, 5 liters, under-sink, low pressure on
92.59 EUR
The AEG U5 small under-sink cylinder provides hot water quickly and conveniently at the kitchen sink. Space-saving and convenient
Due to its compact size, it requires only minimal space under the sink. The temperature of the water flowing out can be continuously adjusted from 30 °C to 85 °C. The 5-liter cylinder heats up particularly quickly thanks to its 2 kW radiator and constantly delivers the desired temperature.
Simple and safe
A safety temperature limiter that can be reset by pulling out the mains plug protects against overheating. The wall mounting strip makes it easy to install the plug-in cylinder.
Note:
This appliance must be used with a low-pressure fitting with 3 connection hoses.
Normal fittings with only 2 hoses will destroy the boiler as the tap water reaches the appliance directly and at full pressure!
Top Pick
FREI KES 2 - Fitted plug for non-heating appliances, vertical attachment
12.38 EUR
Non-heating appliance plug, fitted appliance plug6.3-mm Faston contacts
Excellent
SENSORIT SENSOPROTECT P - SensoProtect Premium, mold warning system
71.92 EUR
Advanced technology for a healthy and comfortable living environment. Measurement of wall and humidity as well as of wall and air temperature above four sensor units, of which one pair is positioned at a distance of 1 mm from the wall, while the second is directed into the room.
Recommended
ACT MOTOR ACT BLDC-8015A-5 - Drivers for BLDC motors
53.57 EUR
ACT Motor GmbH is a high-tech company that specialises in developing and manufacturing hybrid stepper motors, brushless DC motors, servo motors and their drivers.
Featured
EUROPE CHEMI-CON BE KMR 470/450 - Cup electrolytic capacitor, radial, 470 µF, 450 V, 105°C, 30 x 4
16.72 EUR
High-capacity aluminium electrolytic capacitorsKMR series
Electrolytic capacitor with snap-in connections
• Up to 5 mm smaller than the conventional snap-ins from the KMQ series
• Service life with ripple current: 2000 hours at 105°C
• Nominal voltage: 450 V
• Capacity: 470 µF
• Suitable for inverter controllers and switching power supplies
• Not resistant to solvents
Alternative
FREI BE 10.000/25 - Cup-type electrolytic capacitor, radial, 10 mF, 25 V, 85°C, 1200
22.66 EUR
Electrolytic capacitor 10,000 µF/25 VoltAluminium elecrolytic capacitor with solder pin mounting, polarised, switch-proof and short-circuit proof. Small design, high AC load capacity, low ESR, low impedance.
ACT MOTOR ACT BLDC-8015A-0 - Drivers for BLDC motors
53.57 EUR
"- For the BLDC 57BL series motor
- For the BLDC motor with 2 pole pairs, maximum rated speed = 3000 rpm, 24 VDC
CIMCO 187235 - Aderendhülse isoliert 25,0 mm²/22 mm, verzinnt, braun, 50er Pack
24.73 EUR
Isolierte Aderendhülsen, gefertigt aus hochwertigen Kupfer-DHP. Die Oberfläche ist galvanisch verzinnt mit einer Mindestschichtstäke von 3 µm für einen maximalen Korrosionsschutz. Der Kunststoffkragen aus Polypropylen sorgt für ein einfaches Einführen der Kupferleiter. Temperaturbeständig bis 105°C, für Leitungen Klasse 5 / 6 nach IEC 60228
ACT MOTOR ACT BLDC-8015A-8 - Drivers for BLDC motors
53.57 EUR
"- For the BLDC motor 86BLF series
- For the BLDC motor with 4 pole pairs, maximum rated speed = 3000 rpm, 48 VDC
SIEMENS TS SYSTEM ELO - Touch pen system ELO
201.12 EUR
ELO touch pen system for capacitive or resistive touch screen pen ELO, including holder for 22.5 mm, screw on or glue on for capacitive and resistive touch screens.For capacitive and resistive touch screens, pen black anodised and suitable for industrial use, includes holder for gluing or screwing on.
Alternative to touch pen system Alu Classic and touch pen thick resistive
Input aids facilitate operation and input in difficult environments.
Especially when working with gloves, touch pens can often be very helpful when operating touch displays.
Despite wearing gloves, you can operate small buttons or input fields with pinpoint accuracy.
Touch pens also protect the display against dirt and scratches during operation and when operating in extreme environments.
When ordering, pay attention to the touch system (resistive or capacitive).
ACT MOTOR ACT BLDC-8015A-4 - Drivers for BLDC motors
53.57 EUR
"- For the BLDC motor 42BLF series
- For the BLDC motor with 4 pole pairs, maximum rated speed = 4000 rpm, 24 VDC
FREI AX 470/40 - Axial electrolytic capacitor, 470 µF/40 V
10.58 EUR
Axial electrolytic capacitor 470 µF/40 V
CIMCO 187100 - Aderendhülse isoliert 0,14 mm²/6 mm, verzinnt, braun, 100er Pack
14.07 EUR
Isolierte Aderendhülsen, gefertigt aus hochwertigen Kupfer-DHP. Die Oberfläche ist galvanisch verzinnt mit einer Mindestschichtstäke von 3 µm für einen maximalen Korrosionsschutz. Der Kunststoffkragen aus Polypropylen sorgt für ein einfaches Einführen der Kupferleiter. Temperaturbeständig bis 105°C, für Leitungen Klasse 5 / 6 nach IEC 60228
CIMCO 187234 - Aderendhülse isoliert 25,0 mm²/16 mm, verzinnt, braun, 50er Pack
20.39 EUR
Isolierte Aderendhülsen, gefertigt aus hochwertigen Kupfer-DHP. Die Oberfläche ist galvanisch verzinnt mit einer Mindestschichtstäke von 3 µm für einen maximalen Korrosionsschutz. Der Kunststoffkragen aus Polypropylen sorgt für ein einfaches Einführen der Kupferleiter. Temperaturbeständig bis 105°C, für Leitungen Klasse 5 / 6 nach IEC 60228
ECOVACS DEEBOT DKT060203 - Spare parts set for Deebot, 6 pieces
49.22 EUR
"Ecovacs replacement set, for T50 OMNIT50 Family Antibacterial Standard Accessory Set for DEEBOT T50 PRO OMNI
Original ECOVACS accessories:
- 1x main brush
- 2x side brushes
- 3x antibacterial fine dust filters
The T50 MAX Family Antibacterial Standard Accessory Set is the ideal addition for your DEEBOT T50 PRO OMNI robot hoover and mop.
The set includes an Anti-Tangle main brush, two side brushes and three antibacterial fine dust filters treated with silver nitrate and PHMB - for noticeable odor and bacteria reduction.
Original ECOVACS quality ensures a perfect fit, long-lasting performance and thorough cleaning.
The components can be replaced without tools - for fast, uncomplicated replacement."
ECOVACS DEEBOT DKT060175 - Spare parts set for Deebot, 6 pieces
55.33 EUR
"Ecovacs replacement set, for X8 series, DeebotReplacement set (Antibacterial Buddy Kit) for DEEBOT X8 family - For always spotless cleanliness
The replacement kit for DEEBOT X8 family is the perfect accessory for your X8 PRO OMNI or X8 OMNI smart robot mop model. It contains:
- 1x main brush
- 2x side brushes
- 3x antibacterial fine dust filters, treated with silver nitrate and PHMB for more hygiene
This set ensures that your robot always stays in top form - for efficient cleaning and healthy room air. The antibacterial filters minimize the growth of germs and support a particularly clean environment. Ideal for reliably trapping dust, dirt and allergens - extending the service life of your robot and protecting your family in the long term.
Thanks to the uncomplicated installation, you can carry out the replacement without tools and save time - for more convenience when maintaining your robot cleaner."
Small household appliance accessories REICHELT IE Best Products
FREI X7R-5 22N - Multilayer capacitor 22 nF, 50/100 V, X7R 10%, RM 5
10 EUR
Multi-layer ceramic capacitor• Multi-layer technology for high capacitance value per unit volume
• High resonance frequency
• Low ESR value
• Material: X7R
• Max. operating voltage: 50 to 100 VDC
• Tolerance: 10%
• Operating temperature: -55 to +125°C
• Spacing: 5 mm
WALSIN WAL 1206B274K500 - MLCC, 1206, 270 nF, 50V, 10%, X7R
10.06 EUR
Through aggressive mergers and alliances, Walsin Technology Corporation has become a leading global manufacturer of passive components, offering a comprehensive range of products used in virtually all electronic devices.
WALSIN WAL 0805B274K500 - MLCC, 0805, 270 nF, 50V, 10%, X7R
10.12 EUR
Through aggressive mergers and alliances, Walsin Technology Corporation has become a leading global manufacturer of passive components, offering a comprehensive range of products used in virtually all electronic devices.
DIVERSE HERSTELLER AX 105 3300/25 - Axial electrolytic capacitor, 105°C, 16x36 mm, 3300 µF/25 V, low
11.29 EUR
Axial electrolytic capacitor for greater demandsSeries ZA
• Life (charging process) of 2000 h at 105°C
• Low impedance and low ESR for high ripple currents and at high frequency
• Installed in switching power supplies and motherboards
FREI MKH250-7,5 22N - Capacitor 22 N, 250 V
10.22 EUR
MKH (MKT) capacitor - layer capacitor • Type: Film polyethylene terephthalate
• Max. Operating voltage: 250 Volt
• Pitch: 7.5 mm
• Tolerance 5 %
• Temperature range: -55 to +100 °C
PCE INSTRUMENTS PCE CMM 5 - CO2/carbon dioxide meter PCE-CMM 5
185.61 EUR
"PCE-CMM 5 CO2/carbon dioxide meter - Traffic light function
- 5h progress display
- Battery and mains operation. The indoor air quality meter is a CO2 meter for desktop operation. The indoor air quality meter measures the CO2 content in the air and shows the measured value on a large LC display. The CO2 content in the air is an important measure to check the ventilation behaviour in offices, classrooms, lecture halls etc. The indoor air quality meter helps to ensure that, for example, employees in the office ventilate regularly.
Product benefits:
The meter checks indoor air quality via the CO2 content. If the CO2 concentration is below 1000 ppm, the indoor air quality is optimal. Good indoor air quality helps to promote concentration. It also ensures that the aerosol concentration in the air is low, because the aerosols are constantly mixed with fresh air. The indoor air quality meter displays the air quality as a numerical measured value and as a traffic light indicator."
FREI AX 100/25 - Axial electrolytic capacitor, 100 µF/25 V
10.3 EUR
Axial electrolytic capacitor, 100 µF/25 V
FREI KERKO 270P - Ceramic capacitor 270 P
10.01 EUR
Ceramic miniature disc capacitor EGPU have small capacitance tolerances and a high resonant frequency.They are used in audio and video electronics, telecommunications, automotive electronics, information technology, measuring and control technology, medical electronics and much more.
Capacity: 270 pF
Pitch: 2.5 mm
Nominal voltage: 63 V DC
FREI AX 3.300/25 - Axial electrolytic capacitor, 3300 µF/25 V
10.84 EUR
Axial electrolytic capacitor 3,300 µF/25 V
REISSER SCHRAUBENTECHNIK RST 54526/6 - R2 plus pan head chipboard screws, TX, 5.0 x 40 mm, 200 pieces
29.58 EUR
"R2 plus chipboard screw, pan head, 5.0 x 40 mm, partial thread (L1), TX 25, steel, galvanised, blue passivated, EN 14592:2008+A1:2012, 200 pcs. Description
R2 plus chipboard screw - for universal application in interior design, furniture construction, timber construction
PRODUCT FEATURES:
- TX
- Very good power transfer
- No slipping
- Secure mounting
- Pan head
- Flat support surface
- High contact pressure
- Perfect fit and looks good
- Suitable for fittings and fitting parts
- Input thread
- High load capacity
AREAS OF APPLICATION:
- For interior wood connections (interior design, furniture construction, fittings)
MOUNTING RECOMMENDATIONS:
- Pre-drilling may be necessary depending on the condition of the wood and the mounting situation.
Features
- Diameter: d 5.0 mm
- Length: L 40 mm
- Core diameter: d1 3.0 mm
- Thread length: L1 26 mm
- Head diameter: dk 10.0 mm
- Material: steel
- Surface: galvanised, blue passivated
- Drive type: TX
- Drive size: 25
- Head shape: pan head
- Approval: EN 14592:2008+A1:2012
- Package quantity: 200
RAFI 38.83.86 - FS+ 22 — light attachment — round, yellow, flat bezel
15.11 EUR
"RAFIX 22 FS+ light attachment- Round
- Flat bezel
- Translucent yellow
SIEMENS SM 1222 16DO - SIMATIC S7-1200 G2 SM 1222, DO 16x relay/2 A
249.44 EUR
SIMATIC S7-1200 G2: SM 1222 digital output, 16RLY, Outputs: 16x DO, relay 2 A SIMATIC S7-1200 Basic Controller - flexible thanks to a wide range of communication options. With signal modules, you can adapt the configuration of your SIMATIC S7-1200 G2 to suit your specific requirements. A number of digital and analogue input, output and mixing modules are available, also in fail-safe versions. This fine-grained design option saves space in the control cabinet and optimises your hardware costs.
MYWALL MYW HZ22WL - Support Base for Household Appliances, max. 200 kg
33.67 EUR
"The mywall HZ 22 WL rolling frame is the perfect solution for universal applications.With a load capacity of up to 200 kg, it is suitable for easy movement of heavy cases, toolboxes, household appliances and many other applications.
The side length is adjustable from 50 to 70 cm and can be easily adjusted without additional tools using knobs.
For safety, the wheels can be locked and rotate 360°.
Get the practical rolling frame for your universal needs now.
Our tip: Ideal also for large flower pots, for easy moving on the terrace.
- Load up to 200 kg
- for universal use, such as cases, toolboxes, household appliances and flower pots.
- Side length adjustable: 50 - 70 cm
- knobs guarantee easy adjustment without additional tools
- with lockable wheels, 360° rotatable
- including mounting material and mounting instructions
ESKA 140.027 - Car Fuse, 6.3x32mm, 32V, 10A, Glass Tube
11.19 EUR
Quality - Made in Germany!ESKA is one of the internationally leading manufacturers of fuses and produces 100% in Germany - from the idea to the delivery of the finished product.
car fuse, 6,3x32mm, 32V, 10A, glass tube
SIEMENS SIE N 146/03 - IP router Secure
422.36 EUR
"- KNX IP router for networking KNX lines via Ethernet
- Support of KNXnet/IP routing and tunnelling
- Secure communication with KNX IP Secure (encrypted & authenticated)
- Use as a line, area or network coupler
- Up to five simultaneous IP tunnelling connections (e.g. ETS accesses)
- Direct access to KNX systems from the IP network
- Easy integration into visualisation and control systems
- LED displays for KNX and IP communication
- Flexible power supply via PoE or external 24 V
DIVERSE HERSTELLER AX 105 3300/35 - Axial electrolytic capacitor, 105°C, 18x40 mm, 3300 µF/35 V, low
11.71 EUR
Axial electrolytic capacitor for greater demandsSeries ZA
• Life (charging process) of 2000 h at 105°C
• Low impedance and low ESR for high ripple currents and at high frequency
• Installed in switching power supplies and motherboards
SIEMENS TS KAPPE ELO - Touch pen caps ELO
69.74 EUR
ELO touch pen caps, replacement caps for touch pen systems for capacitive and resistive Input aids facilitate operation and input in difficult environments.
Especially when working with gloves, touch pens can often be very helpful when operating touch displays.
Despite wearing gloves, you can operate small buttons or input fields with pinpoint accuracy.
Touch pens also protect the display against dirt and scratches during operation and when operating in extreme environments.
When ordering, pay attention to the touch system (resistive or capacitive).
SMC PNEUMATIK VXZ262KLA - Process valve 2/2 for air/water, NC, 230 VAC, brass, G1
207.16 EUR
Process valve 2/2 for air/water, NC, 230 VACPilot controlled solenoid valve 2/2, without minimum differential pressure
For compressed air, water
Electrical connection: DIN terminal
Housing: Brass
SMC PNEUMATIK VXD242HLA - Process valve 2/2 for air/water, NC, 230 VAC, brass, G1/2
105.35 EUR
Process valve 2/2, NC, 230 VACCompact, directly operated 2/2-way solenoid valve
For compressed air, water
Electrical connection: DIN terminal
Housing: Brass
Seal: NBR
DIVERSE HERSTELLER AX 105 3300/50 - capacitor, axial, 3.3 mF, 50 V, 105°C, 20%
12.95 EUR
Axial electrolytic capacitor for increased requirements- Installed in switching power supplies and motherboards
REISSER SCHRAUBENTECHNIK RST 54344/6 - R2 plus pan head chipboard screws, TX, 3.0 x 25 mm, 200 pieces
15.94 EUR
"R2 plus chipboard screw, pan head, 3.0 x 25 mm, partial thread (L1), TX 10, steel, galvanised, blue passivated, EN 14592:2008+A1:2012, 200 pcs. Description
R2 plus chipboard screw - for universal application in interior design, furniture construction, timber construction
PRODUCT FEATURES:
- TX
- Very good power transfer
- No slipping
- Secure mounting
- Pan head
- Flat support surface
- High contact pressure
- Perfect fit and looks good
- Suitable for fittings and fitting parts
- Input thread
- High load capacity
AREAS OF APPLICATION:
- For interior wood connections (interior design, furniture construction, fittings)
MOUNTING RECOMMENDATIONS:
- Pre-drilling may be necessary depending on the condition of the wood and the mounting situation.
Features
- Diameter: d 3.0 mm
- Length: L 25 mm
- Core diameter: d1 1.8 mm
- Thread length: L1 16 mm
- Head diameter: dk 6.0 mm
- Material: steel
- Surface: galvanised, blue passivated
- Drive type: TX
- Drive size: 10
- Head shape: pan head
- Approval: EN 14592:2008+A1:2012
- Packaging classification: small package
- Package quantity: 200 pieces